Shifter vs Console Question

[aakate]

Just wonder if someone makes a automatic shifter for c4 that will fit in a 95 Cobra without having to butcher up the factory console. My interior is in ment condition and would like to keep it that way but still have good performance. Thanks in Advance

[86GTPONY]

Just wonder if someone makes a automatic shifter for c4 that will fit in a 95 Cobra without having to butcher up the factory console. My interior is in ment condition and would like to keep it that way but still have good performance. Thanks in Advance
Summit has a B&M Shifter (part# BMM-81002) and the adapter for a c-4 trans (part# BMM-81020) - You could probably look ath the dimensions to see if it will fit in your console without having to butcher it...or just call their tech line.

[SlowJoe]

the first one is a video and the other 2 are the parts.




http://www.youtube.com/watch?v=0htlF2pTb5s&eurl=http://www.allfordmustangs.com/forums/94-95-tech/129373-automatic-shifter-1995-mustang-gt-2.html


http://www.bmracing.com/s.nl/c.723089/n.2/it.A/id.108/.f?sc=17&category=6029



http://www.bmracing.com/s.nl/c.723089/n.2/it.A/id.409/.f?sc=17&category=6053

[waypastcrazy]

Just wonder if someone makes a automatic shifter for c4 that will fit in a 95 Cobra without having to butcher up the factory console. My interior is in ment condition and would like to keep it that way but still have good performance. Thanks in Advancealso needs to work with reverse valve body. Lol

[SlowJoe]

that one will do it even has a button you can wire reverse up to.

[SlowJoe]

i just found 1 post that says the straight shift tunnels are bigger and shifter would set a little higher. but that was just 1 post. anyone else know anything about this?:think:

[coupe]

I used a stock AOD shifter on my rev. manual C4. You might be able to use your stocker by disassembling it and modifying the detents. :shrug:

There's not much room in the SN95 console/dash area.

[aakate]

Thanks for all the info !!!! Lots of help

[SlowJoe]

i will be coping your setup next year so i will have to check it out when u get done. i looked at 04mach1 shifter like that sunday. it looks sweet. and his is on a reverse manual trans. i should have felt of it and shifted the gears.

[aakate]

i will be coping your setup next year so i will have to check it out when u get done. i looked at 04mach1 shifter like that sunday. it looks sweet. and his is on a reverse manual trans. i should have felt of it and shifted the gears.

I was checking out the quaterstick shifter. Gonna call get some specs on one

[SlowJoe]

I was checking out the quaterstick shifter. Gonna call get some specs on one

i had one they are nice! remember the one i had in the coupe. just need to come up with something to mount it.

[Craig K.]

FYI - If your in the B-Ham area, I was at pull-a-part a two weeks ago and there was an automatic SN-95 (I think a 1994) IIRC it still had the console and shifter, you could probably get it real cheap and proto-type off of that instead of butchering yours. I believe it was gray.

[qkjuicedpony]

Get a quarter stick and make a plate to sit the shifter down inside the stock shifter hole.

put your leather boot over the shifter and it looks factory.

ive done it once or twice.

[aakate]

Thanks Craig K, But B ham is about a three hour drive from here in N.E. Corner Of Mississippi

[aakate]

Get a quarter stick and make a plate to sit the shifter down inside the stock shifter hole.

put your leather boot over the shifter and it looks factory.

ive done it once or twice.

Thanks for info.

[aakate]

The time has come to slip PA C4 Comp In

Thanks for all the info years ago folks!!!

And a special thanks for waypastcrazy (Clyde),
He bought me a 28oz flex plate and had it shipped to my house yesterday.
No questions asked, except one, confirm a 157 tooth count

All I like now to start is to have one of the torque convertor bolts welded back on
And put that baby in....