combo

[SlowJoe]

there is a guy in ga i grew up with that we have not always seen eye to eye with each other! anyways i have been workin on budget gt for a buddy and we have it close. and mark (the guy i dont see eye to eye with) and one of his rich buddy is building a 95 gt. And the smack talk has started!!! just want to see where we stand.

his specs
95 gt
306 (86 model block)
12.1 dome pistons(as he says) i seen them and they are pop ups:jester:
steel crank
I beam rods
gt40y alum heads
X cam
victor intake
750 hp holley
200 shot of n2o
red neck c4 with 3000 stall
3.55 gears

O and nothing is being balanced or checked

our combo

90 gt
302 (over 100000 miles)
b cam
torker 289 intake
650 dp holley (running 12.5 AFR :jester:)
150 shot n2o
5 speed
3.73 gears

i spent all day sat on this carb!!! it is crisp:metal:

so are we going to get smoked?

[SvoBrown]

uh yep

[acproxer]

just like pinks, you better negotiate a few car links

[blue90lx]

:lol:

[SlowJoe]

just like pinks, you better negotiate a few car links

i dont think so! i think we gona take him

[EHardy1971]

And the smack talk has started!!!

YOU talk smack? I'm shocked!:jester:

his specs

12.1 dome pistons(as he says) i seen them and they are pop ups:jester:

gt40y alum heads
X cam

O and nothing is being balanced or checked



:hmm: I'm betting his piston to valve clearance not being checked with that setup might bite him in the ass.

[SlowJoe]

YOU talk smack? I'm shocked!:jester:


:hmm: I'm betting his piston to valve clearance not being checked with that setup might bite him in the ass.

i never talk smack!!! everyone else does and i just back mine up:jester:

i dont think it will make it! Glad o boy is rich

[rtusnake]

What part of ga are they from?

[SlowJoe]

What part of ga are they from?

waco.

[waypastcrazy]

there is a guy in ga i grew up with that we have not always seen eye to eye with each other! anyways i have been workin on budget gt for a buddy and we have it close. and mark (the guy i dont see eye to eye with) and one of his rich buddy is building a 95 gt. And the smack talk has started!!! just want to see where we stand.

his specs
95 gt
306 (86 model block)
12.1 dome pistons(as he says) i seen them and they are pop ups:jester:
steel crank
I beam rods
gt40y alum heads
X cam
victor intake
750 hp holley
200 shot of n2o
red neck c4 with 3000 stall
3.55 gears

O and nothing is being balanced or checked

our combo

90 gt
302 (over 100000 miles)
b cam
torker 289 intake
650 dp holley (running 12.5 AFR :jester:)
150 shot n2o
5 speed
3.73 gears

i spent all day sat on this carb!!! it is crisp:metal:

so are we going to get smoked?I don't think the 95 will make the race. I know budget gt will. Lol!

[waypastcrazy]

there is a guy in ga i grew up with that we have not always seen eye to eye with each other! anyways i have been workin on budget gt for a buddy and we have it close. and mark (the guy i dont see eye to eye with) and one of his rich buddy is building a 95 gt. And the smack talk has started!!! just want to see where we stand.

his specs
95 gt
306 (86 model block)
12.1 dome pistons(as he says) i seen them and they are pop ups:jester:
steel crank
I beam rods
gt40y alum heads
X cam
victor intake
750 hp holley
200 shot of n2o
red neck c4 with 3000 stall
3.55 gears

O and nothing is being balanced or checked

our combo

90 gt
302 (over 100000 miles)
b cam
torker 289 intake
650 dp holley (running 12.5 AFR :jester:)
150 shot n2o
5 speed
3.73 gears

i spent all day sat on this carb!!! it is crisp:metal:

so are we going to get smoked?I don't think the 95 will make the race. I know budget gt will. Lol!big money parts don't mean sqaut in the wrong hands.seen it to many times.

[uedlose]

sounds like he is building a bomb to me. so while he may beat you down the track I would think your set up will be around racing longer then his will.

[coupe]

Might be "close enough" on the balance. :D


Seriously though, a 12:1 compression 306 with a 750dp and X303 cam would be a real rocket...especially with a 200-hit. Good luck!

[SlowJoe]

they have done built one motor for it with a blower and blew it up in a week

[jonosranger]

:rofl:

[97cobrasvt]

I know a good working motor means alot but what kind of suspension are you running? If you set it up right and can leave on him good enough you can out run alot of people with alot more HP. Suspension means alot guessing you are going to run a 1/8 mile right?

[SlowJoe]

yea 1/8 mile. right now it is stock but we are working on that

[QWKSNKE]

Compression definitely gives an advantage if the motor runs right

[EHardy1971]

Compression definitely gives an advantage if the motor runs right
And if he's running the right fuel. I don't see it running on pump gas.

[SlowJoe]

we talked about budget GT today its getting a set of heads in 2 weeks!:metal:

[waypastcrazy]

Compression definitely gives an advantage if the motor runs rightnot if the dome interferes with flame front which happens with most dome pistons unless the engine has a custom ground cam and or the the trough cut across the dome like diamond does.I learned that one the hard way lol.
Just pissing in the wind grabbing an off shelf cam and throwing domes at a motor unless it has been researched lo

[waypastcrazy]

But yea compression is a good advantage. Domes are just not the idea way to get it.

[QWKSNKE]

.
Just pissing in the wind grabbing an off shelf cam and throwing domes at a motor unless it has been researched lo

agreed

[SlowJoe]

just worked a deal on a set of these:popcorn:

http://www.powerheads.com/images/FLOW-TEST-289-302.gif

[waypastcrazy]

just worked a deal on a set of these:popcorn:

http://www.powerheads.com/images/FLOW-TEST-289-302.giflook at the exhaust numbers. Them will wake it up.

[SlowJoe]

look at the exhaust numbers. Them will wake it up.

got the set with 1.6 roller rockers for 500:banana: now got to see what we can come up with on a cam.

[BAD INT]

....................

[SlowJoe]

what suspension is on the car front and rear

stock right now. but its got to have some work in the back bad

[waypastcrazy]

got the set with 1.6 roller rockers for 500:banana: now got to see what we can come up with on a cam.after what I saw in the last 2 evans boys motors I would get it from lem if ya can catch him between qaurts of ky spring water lmao! He knows his stuff and they are only 15 bucks more than an off shelf cam.

[SlowJoe]

we are pulling the motor in to weeks lmao:crazy: putting new rings and bearings. bolting heads on and gona see how much of a shot it will take!

[BAD INT]

.................................

[SlowJoe]

what cam are you thinking also??

go for the budget saver find some used south sides and adj uppers,

i am thinking about a NOS cam because it will not be raced with out it.

[BAD INT]

....................................

[SlowJoe]

I have a roller that would work well listed in the for sale section

Lunati hydraulic roller cam 51012 .544 .560

whats lobe seperation?

[waypastcrazy]

what cam are you thinking also??

go for the budget saver find some used south sides and adj uppers,x2. Lmao I took the good stuff off of it.

[BAD INT]

.............................................

[SlowJoe]

112 pretty sure,you can get info on the lunati site I dont have the card anymore

yea just looked it up. its a 112. thats a lot of lift!! let me study it.

[BAD INT]

.................................................. ...

[SlowJoe]

went 6.50's with stock shortblock and out of box vic jr's on hose

how much of a hose

[blue90lx]

:popcorn:

[BAD INT]

......................................

[97cobrasvt]

If you are looking for a solid roller I have one. Its the cam that came out of my motor when I ordered my custom nos cam. It has a 110 lobe seperation but I dont remember off the top of my head the rest. I do have the cam card at home so let me know.