PDA

View Full Version : Cheap and easy plastic headlight restoration.


EHardy1971
10-15-2009, 08:11 PM
I know most of us here have vehicles with factory plastic headlights (especially Foxes and SN95's), that are notorious to hazing/yellowing over time, and exposure to the elements. I've taken some techniques that I've read about, and combined them with some of my own ideas, which turned out very good results. Here's what you'll need....

SOS soap pads ($1 at Dollar general)
1 small pack of 1500 grit wet/dry sandpaper ($3 at Oreilly's)
1 bottle of plastic polish (I recommend Meguiars Plast-X $5)
Terry cloth towel
Old spray bottle with mixture of dish soap and water (to aid in wet sanding)
Optional:Buffing/polishing wheel kit for cordless drill ($10 at Home depot)

Here's the lights before being touched,

http://i273.photobucket.com/albums/jj228/ehardy1971/IMG_1498.jpg

After initial scrubbing with SOS pad to remove the yellowed, oxidized layer..

http://i273.photobucket.com/albums/jj228/ehardy1971/IMG_1500.jpg

after wet sanding with the 1500 grit. Be sure to keep them wet with the spray bottle while sanding, when the sandpaper starts to "glide" across the surface, they're sanded enough....

http://i273.photobucket.com/albums/jj228/ehardy1971/IMG_1504.jpg

..now, apply a small amount of the Plast-X to the terrycloth towel, and polish in circles like waxing a car. You'll start to see the results immediately...

http://i273.photobucket.com/albums/jj228/ehardy1971/IMG_1507.jpg

Now for the optional final step (which I REALLY recommend!). The buffing wheel and white plastic cleaner/polish stick from the polish kit...

http://i273.photobucket.com/albums/jj228/ehardy1971/IMG_1505.jpg

...if you've never used this kind of buffing wheel, all you do is spool up the drill, and stick the polish to it with medium pressure. It doesn't take much polish to get on the buffing wheel to do the job. After the polish is in the buffing wheel, run it in straight, overlapping lines back and forth, again using medium to light pressure. This step REALLY brings them to an almost new condition!
http://i273.photobucket.com/albums/jj228/ehardy1971/IMG_1508.jpg
http://i273.photobucket.com/albums/jj228/ehardy1971/IMG_1502.jpg

Before and after comparison..

http://i273.photobucket.com/albums/jj228/ehardy1971/IMG_1511.jpg

Time spent, roughly 30 minutes per side, of course this depends on the condition of the lights when you start too.:nice:

klu408
10-15-2009, 08:53 PM
Looks Great Eric

TheJeanyus
10-15-2009, 08:58 PM
Nice work. :nice:

hevymtl
10-15-2009, 09:18 PM
:nice:

EHardy1971
10-15-2009, 09:44 PM
Thanks! :D

SilverBack
10-16-2009, 05:25 AM
Made a huge difference!

I used the chemical stuff on my wife's civic about a year ago and it's still holding up pretty well. Basically do the same steps you did but instead of a final polish/buff, you just wipe it down with the provided cloth and it becomes clear and hardens that way.

Nice way to save some bucks!

lukem80
10-16-2009, 08:55 AM
thats pretty cool

I just wet sand 2000 grit till all the yellow is gone

then I hit it with a few coats of clear

EHardy1971
10-18-2009, 09:57 PM
Finished product (right side looks cloudy from moisture)...


http://i273.photobucket.com/albums/jj228/ehardy1971/IMG_1525.jpg



http://i273.photobucket.com/albums/jj228/ehardy1971/IMG_1529.jpg

and finally a before and after of the overall effect...

before...

http://i273.photobucket.com/albums/jj228/ehardy1971/IMG_1455.jpg

after...

http://i273.photobucket.com/albums/jj228/ehardy1971/IMG_1526.jpg


and yes, my car needs to be washed.:brick:

itlepeanut
10-19-2009, 05:52 AM
:spit:Kittah paws................:poke:

stangman
10-19-2009, 06:21 AM
I usually wipe and clear coat them. They will look new.

coupe
10-19-2009, 03:41 PM
Cool! I've cleaned up my lights a few times like that. The last polishing step really makes the difference for sure!

But heck...foxbody lights are only $99 for the entire set of 6... saves me the hassle and they ALL look new at that point. LOL. (Reminds me.. I need to buy a couple sets of them :D)

BeachBoy
07-29-2010, 08:09 PM
I know most of us here have vehicles with factory plastic headlights (especially Foxes and SN95's), that are notorious to hazing/yellowing over time, and exposure to the elements. I've taken some techniques that I've read about, and combined them with some of my own ideas, which turned out very good results.

Excellent.

Thanks for the tip!





.

CrimsonRacing
07-30-2010, 12:51 AM
when I still had the '88,I used 3m paste cleaner and a buffing wheel.....


Made them look almost better than new...........took about 30min per lite,but I was happy.



:metal:

SvoBrown
07-30-2010, 03:10 AM
About $285 for the svo lights. And I still can't get the outer marker lights. Time to do it again.

86GTPONY
07-30-2010, 07:15 AM
About $285 for the svo lights. And I still can't get the outer marker lights. Time to do it again.

Same goes for the Turbo Coupe - If you can find em new, they cost a lot! I use 1500 and some polishing compound, then use a polishing wheel on a drill... works pretty good.