PDA

View Full Version : EvM Tri-Link install on a 96 Cobra *DUW*


Sendero
01-04-2005, 09:24 AM
In this post I will be detailing the installation of the EvM Tri-Link suspension component on a 1996 Cobra. Throughout the install I tried to take pictures and notate the individual steps that are of interest. If you have any specific questions about the install, just ask.

Car Specs

Front:
350lb MM Coil-overs
Bilstein Sport Strut
Stock Cobra Swaybar
Lowered 1” (27” ground to fender)

Rear:
225lb MM Coil-overs
Bilstein Sport Shock
MM Panhard Bar
Pro3i Race LCA’s (MM Knock offs)

Product

Most of you know about the EvM Tri-Link and what it does. If not you can read about it HERE. (http://www.evolutionmsport.com/evmCart/index.php?main_page=product_info&cPath=1&products_id=2&zenid=73a2a2413de304dc32cfb530d11ab8dc) When the kit finally arrived I was impressed by the workmanship and finish of the parts. It’s not some cheap, flimsy, piece of junk that we have seen from other “suspension” companies. Although mine did not come with instructions (because it was the first production run) I received all of my parts in one shipment. If you would like to see what the kit looks like right out of the box, click HERE. (http://corner-carvers.com/forums/showpost.php?p=274263&postcount=171)

Preparation

Because I will be driving more that 150 miles away to install this kit I tried to do as much preparation as possible. Gathering up all the tools, inventory of all the parts, and reading through the instructions at least three times.

I removed the rear seat delete and started with the first steps of the instruction, removing the mastic on the floor pan. I took the reinforcement plates and scribed a mark into the surrounding the mastic. Then using a scraper I removed the mastic as best I could. To clean up the adhesive I sprayed it down with some gasket remover and wiped up the byproduct with a paper towel.

Nice and clean!
http://www.senderosnake.com/graphics/trilink/masticremoved.jpg

Rear Cradle

After I got the car up on the lift and removed the panhard bar, I started on the rear cradle. Dumped the UCA’s and bushings in about 10 minutes, it was a breeze with the MM bushing tool. If you don’t have one, get one!

http://www.senderosnake.com/graphics/trilink/MMtool.jpg

You have to do some creative stacking, but you can use the MM tool to install the solid bushings from the kit. The rest of the rear cradle install was easy as I had a stock differential cover.

http://www.senderosnake.com/graphics/trilink/rearcradeinstalled.jpg

Front Cradle

Next to go in was the front cradle. You are going to have to at least undo the exhaust hanger brackets to get the cradle in there. You can get away with keeping the driveshaft in place, but it’s a good idea to remove it for added elbow space. Also, undo the brake and fuel lines retainers located in the trans tunnel and the trunk floor.

I went ahead and assembled the front “center link” attachment on the front cradle. This is where I ran into my first problem. It seems that the cap screw for the center link attachment was too long. Whenever I screwed the cap screw all the way in it was hitting the other side of the cradle leaving a 1/16” gap between the screw’s shoulders and mounting ear.

EDIT: EvM has fixed this problem. My kit was one of the first produced which had some slight changes from the pre-production units. All kits are shipping with the correct washer stack.

http://www.senderosnake.com/graphics/trilink/frontspace.jpg
http://www.senderosnake.com/graphics/trilink/frontspacetwo.jpg

So I took one of the extra washers from the kit and added it to the stack.

http://www.senderosnake.com/graphics/trilink/spacestack.jpg
NOTE: This is not a recommended fix.

Then using a ½” Hex Head socket I torqued the cap screw to 120 ft-lbs. (It did not say to in the instructions, but the rear of the link attachment was at this spec) Now you are ready to fish the cradle up into the tangle for single shear attachment. You could do this part alone if you’re part primate, but it took me: two humans, four hands, and one foot to complete this mount.

http://www.senderosnake.com/graphics/trilink/singleshear.jpg

With the UCA attachments cinched up, its time to mark the floor pan for the U-bolts and “through bolt” holes for drilling. EvM’s instructions on marking the U-bolts are the best method, but I have something to share on how I marked the “through bolt” hole. Using a mechanics mirror (little bit bigger than the mirror your dentist uses) and a light I was able to bounce the light through the hole which came out as a perfect circle on the other side. (Thanks Brian) Another person was then able to mark the center of the “light” circle with a sharpie pen. This proved to make an accurate hole for the cradle.

http://www.senderosnake.com/graphics/trilink/transtunnel.jpg

For some reason, my cradle mounted much higher in the trans tunnel than the one pictured in the instructions. My through bolt was REALLY long and I had to trim a lot off of the spacers provided for the front of the cradle. I ended up using the interior spacers on the exterior and exterior spacers on the interior. The stack ended up looking like this:

Starting from Drivers Side = Exterior Spacer – Plate – Body – Washer – Interior Spacer – Cradle – Exterior Spacer – Washer – Body – Plate – Interior Spacer

Front Cradle finished:
http://www.senderosnake.com/graphics/trilink/fcradleinstalled.jpg
http://www.senderosnake.com/graphics/trilink/fcradleinstalled2.jpg


Center Link

Nothing to exciting enough to report here. Just make sure you have the length correct and you torque the rear attachment correctly. Don’t forget to tighten the jam nuts or you could have a nasty surprise later!

Here it is, buttoned up and ready for the drive home:
http://www.senderosnake.com/graphics/trilink/sideshot.jpg
http://www.senderosnake.com/graphics/trilink/installed.jpg

OPTIONAL: Double Shear Mounting, the $50 upgrade

Since I intend to race this car at some point, I decided to do the double shear mounting. Whoa, there should have been a bigger warning in the instructions about this!

First, following the instructions was not the way I was able to install the longer bolts. Maybe my floor pan is different, but as soon as I undid the UCA attachments, the cradle moved enough that the holes were no longer in alignment. The only option I had after prying on the bar for 30 minutes was to completely remove the front cradle. After walking the holes just a little and screwing up the threads on the cradle, a light bulb went off.

Presenting my Double Shear Mounting measurement tool:
http://www.senderosnake.com/graphics/trilink/dblsheartool.jpg

I found two “junk” ½” bolts and cut just enough off of the bolt to allow it to pass between the UCA’s mounting points. This way I can thread the “tool” into one side of the cradle with the other side of the cradle tightened down via the single shear mount. As you can see from the pictures below, I now know how much to remove from the outer UCA mounting hole judging by how the “tool” sits in relation to the outer hole. Rinse and Repeat for the other side.

http://www.senderosnake.com/graphics/trilink/dblshearcut.jpg
http://www.senderosnake.com/graphics/trilink/dblshearcut2.jpg

Using a high speed drill and a metal rasp I was able to elongate the hole just enough to finish the double shear mount. TIP: It would be wise to chase all threads with the appropriate tap and dyes. This will help you get that “feel” so you don’t cross thread anything! DON’T MAKE MY MISTAKE!

Here is the double shear completed, it better be worth it!
http://www.senderosnake.com/graphics/trilink/dblshear.jpg

Final Thoughts and Driving Impressions

Right off the bat, I noticed a drastic difference in the “feel” of my car. The tires bite extremely hard now and upshifts are met with a nice chirp instead of tire spin. Also, in off camber situations (speed bumps, uneven pavement, and potholes) the rear acts just like an IRS rear in that it flexes without the other tire leaving the ground or excessive body input. I set the anti-squat in the middle for testing purposes. No brake hop to report or any handling “surprises.” However, the noise increases two-fold with the addition of the solidly mounted axle. If you have a bad gear install or failing limited slip, you will know it post haste. I think I can make out the spider gears swirling around in the differential as the car is decelerating to a stop. EvM has said that most of their products will be marketed towards the “street performance” crowd, but I think the noise level will put it up towards hardcore idiots (like me) or the race only crowd. I won’t have any track time (drag or road course) for a couple of weeks, but I will report back when I do. If you have any questions, please ask.

Overall, I am EXTREMELY please with the product. There are still some nit-picking things to iron out in the instructions and maybe some small product changes. I will recommend this product to anyone looking to improve their rear suspension.

Thanks to Lee, Brian, Joseph, and Matt for providing manual labor. Allan for usage of your shop. Jennifer and Meredith for getting lunch. You guys are awesome!

EZ SPEED
01-04-2005, 10:03 AM
Good Job Nathan!!

The Rock 326
01-04-2005, 12:03 PM
Looks sweet! :chug:

Scothew
01-04-2005, 01:06 PM
great write up Nathan

GoldnGT
01-04-2005, 01:36 PM
nice writeup man. Put that one down in the books.

Mike

TheJeanyus
01-04-2005, 01:46 PM
Have you put the RSD back in? Is it still really loud inside with it back in?

Sendero
01-04-2005, 02:39 PM
Have you put the RSD back in? Is it still really loud inside with it back in?

Not to loud. About as noisy as my race LCA's. But there is a resonance around 70+ mph that can get annoying. I am thinking of wraping the center link in some sort of rubber in an effort to kill the noise.

TheJeanyus
01-04-2005, 03:52 PM
Maybe that stuff KB used in his '03 L would work? :shrug:

Italian LX
01-04-2005, 04:06 PM
Not to loud. About as noisy as my race LCA's. But there is a resonance around 70+ mph that can get annoying. I am thinking of wraping the center link in some sort of rubber in an effort to kill the noise.
I doubt that will work. The noise is being transfered through the solid spherical bushings. You no longer have the non-metal bshings absorbing the road noise.

FastRedPonyCar
01-04-2005, 04:16 PM
Awesome nate. I was watching their stuff like a hawk. I was actually very close to buying their project 03 GT which had the watts setup, 3 link, sypder brace up front, full subframe kit and full spintech exhaust and 150 shot N2O kit.

As with all brand new products, there's always bound to be a few engineering mis-calculations. Same thing happend with their radiator V-brace that I installed. Their directions had no mention of the oil cooler which was on my car and in the way of the install :(

I forget which guy it was that works there but he gave me a discount on my next purchase there and a free T-shirt!

Sendero
01-04-2005, 07:10 PM
I doubt that will work. The noise is being transfered through the solid spherical bushings. You no longer have the non-metal bshings absorbing the road noise.

Not kill the noise per say (I'd do that with sound deadening the interior), but to change the frequency of the noise. Right now its sort of sharp at anything above 65mph. Hopefully the rubber would "dull it down" some. Kind of like hitting a tuning fork then touching it with your finger.

Craig K.
01-04-2005, 07:24 PM
Great write up Nathan, wish I could have given a helping hand in the install.

When is the first track day, and where?

Sendero
02-27-2005, 11:03 AM
Update:

After putting a couple thousand street miles on the car I am happy to report everything is still as it should be. This weekend I decided to do a little maintenance and swap in my 275lb springs in place of my 225lb springs. Checking all the bolts and attachment points everything was in order and within spec. Before swapping the springs I was expecting a much stiffer ride because of my past bone-jarring experience with the 275lb'ers. (This was on a stock suspension with the PHB) Well, I was wrong about that ride quality. With the 225lb springs I was experiencing a some "buggy bouncing" as I went over bumps and bridge jounts, almost like the rear was oscillating out of control. But with the 275lb springs the bouncing has all but stopped and the car is flatter throughout turns, both sharp and sweeping. I still could stand a tad more rebound valving from the Bilsteins, but I am very pleased with how it has turned out.

Now I just have to figure out what I want to do with the front.

96GTS
02-27-2005, 12:33 PM
Update:

After putting a couple thousand street miles on the car I am happy to report everything is still as it should be. This weekend I decided to do a little maintenance and swap in my 275lb springs in place of my 225lb springs. Checking all the bolts and attachment points everything was in order and within spec. Before swapping the springs I was expecting a much stiffer ride because of my past bone-jarring experience with the 275lb'ers. (This was on a stock suspension with the PHB) Well, I was wrong about that ride quality. With the 225lb springs I was experiencing a some "buggy bouncing" as I went over bumps and bridge jounts, almost like the rear was oscillating out of control. But with the 275lb springs the bouncing has all but stopped and the car is flatter throughout turns, both sharp and sweeping. I still could stand a tad more rebound valving from the Bilsteins, but I am very pleased with how it has turned out.

Now I just have to figure out what I want to do with the front.
good to see its holding up. :metal:

Next big purchase should be some Koni DAs ;)

FastRedPonyCar
02-28-2005, 09:03 AM
Update:
both sharp and sweeping..

What about flat sweeping? :dunno:

Jugg2Driver
03-01-2005, 04:04 PM
Very informative Nathan!

93Cobra#2771
07-28-2005, 12:20 PM
TTT - after many more miles, any problems to report? Do you regret the increased NVH levels with the solid attached rearend? Is your car a daily driver or a weekend thrasher?

Sendero
07-28-2005, 01:05 PM
TTT - after many more miles, any problems to report?

Nope. Just two weeks ago I crawled under the car with a torque wrench in hand to make sure nothing was out of spec. Not one bolt was loose or were any parts fo the kit showing signs of wear.

Do you regret the increased NVH levels with the solid attached rearend?

In all reality, my Race LCA's seem to be the biggest noisemaker BEFORE I put the "Brown Bread" (http://forums.qwiksnake.com/showthread.php?t=1612) sound deading in. I wouldn't think they would be much louder than Dronemaster 40's and a off-road H-pipe. There are no standout Vibrations or Harshness to report because the car actually rides smoother now.

Is your car a daily driver or a weekend thrasher?

Daily Driver. Rain, Shine, Sleet, Snow, and Hail. Its the Post Office Cobra with over 12,000 mile average per year. I'm taking it to the beach this weekend and its been on several LONG trips with the Tri-Link on.

93Cobra#2771
07-28-2005, 01:53 PM
The PHB you have - It's the MM unit, right? Stock tailpipes? I'm looking at a MM on ebay right now, NIB. Seriously considering going with it and the EVM piece. :D

Sendero
07-28-2005, 08:51 PM
The PHB you have - It's the MM unit, right? Stock tailpipes? I'm looking at a MM on ebay right now, NIB. Seriously considering going with it and the EVM piece. :D

:yup: Its a MM PHB with the Aluminum Bar. I really like the piece, but considering what I am building the car for, I would have installed a watts-link instead. The PHB will work with most tailpipes all the way up to 3" systems. I think MAC's are the only ones which have clearance problems, but send an email to MM and ask. They are VERY helpful even if you are'nt buying directly from them.

If you do get it, I can lend a brain on the install because its a little daunting.

Italian LX
07-28-2005, 09:09 PM
. . . with over 12,000 mile average per year.
Rookie. :rolleyes:


:D

93Cobra#2771
07-29-2005, 06:23 AM
:yup: Its a MM PHB with the Aluminum Bar. I really like the piece, but considering what I am building the car for, I would have installed a watts-link instead. The PHB will work with most tailpipes all the way up to 3" systems. I think MAC's are the only ones which have clearance problems, but send an email to MM and ask. They are VERY helpful even if you are'nt buying directly from them.

If you do get it, I can lend a brain on the install because its a little daunting.

Yeah, I read through the installation instructions - they did seem a little involved.

I will definitely get in contact if I go this route.

No reason for me to go with a watts link - I won't come close to even maximizing the PHB setup. Hell, I haven't even come close to maximizing my stock setup... :lol: