StreetStangs.net - Search Results

		StreetStangs.net > Search Forums
Search Results

Showing results 1 to 9 of 9
Search took 0.00 seconds. Search: Posts Made By: QWKSNKE

Forum: Dyno Room

04-10-2007, 02:20 PM

Replies: 34

Crzypny's 94 GT

Views: 18,121

Posted By QWKSNKE

rockers would be a whole lot easier to change vs...

rockers would be a whole lot easier to change vs a cam swap. Besides, while the 'b' cam is a old design it is still a good cam. I proved that with my first combo on the cobra

Forum: Dyno Room

04-08-2007, 05:53 PM

Replies: 34

Crzypny's 94 GT

Views: 18,121

Posted By QWKSNKE

driveshaft won't cause a power loss it will just...

driveshaft won't cause a power loss it will just suck when you carry it up in the rpms.

I agree with qkjuiced. The clutch could be causing a problem since it is the OEM one. It may be slipping...

Forum: Dyno Room

04-08-2007, 05:42 PM

Replies: 34

Crzypny's 94 GT

Views: 18,121

Posted By QWKSNKE

They were not noisy when I drove it after...

They were not noisy when I drove it after installing 3.73's a few months ago.

Forum: Dyno Room

04-08-2007, 05:40 PM

Replies: 34

Crzypny's 94 GT

Views: 18,121

Posted By QWKSNKE

stud mount

stud mount

Forum: Dyno Room

04-08-2007, 05:39 PM

Replies: 34

Crzypny's 94 GT

Views: 18,121

Posted By QWKSNKE

yeah I know. The 39 and 10 I referred to is the...

yeah I know. The 39 and 10 I referred to is the preferred settings at idle when EEC tuning

Forum: Dyno Room

04-08-2007, 05:12 PM

Replies: 34

Crzypny's 94 GT

Views: 18,121

Posted By QWKSNKE

I doubt the b cam is hurting it. I made 295rwhp...

I doubt the b cam is hurting it. I made 295rwhp with a b cam and 1.7 rockers.

EEC tuning should have been done with fuel press at 39 psi (vacuum off) and base timing set at 10 degrees.
What...

Forum: Dyno Room

04-08-2007, 03:46 PM

Replies: 34

Crzypny's 94 GT

Views: 18,121

Posted By QWKSNKE

I was wondering that as well. Did you notice the...

I was wondering that as well. Did you notice the curve on Crzpny's at 5400 or so. Shouldn't it have kept going up or at least stayed flat and then fall at 6k rpm. I figure the tfs intake would flow...

Forum: Dyno Room

04-08-2007, 02:30 PM

Replies: 34

Crzypny's 94 GT

Views: 18,121

Posted By QWKSNKE

Just my 2 cents.. IF the valve covers allow...

Just my 2 cents..

IF the valve covers allow it, remove the spacer. Its hurting the upper rpm power. I am in the same boat but I had to use a spacer to get my intake to clear the valve covers

Forum: Dyno Room

04-08-2007, 02:24 PM

Replies: 34

Crzypny's 94 GT

Views: 18,121

Posted By QWKSNKE

This guy had some similar results. ...

This guy had some similar results.
http://www.svtperformance.com/forums/showthread.php?t=377501

I guess the tfs kit does not make the power that it seems like it would :shrug:

The tune is...

Showing results 1 to 9 of 9

All times are GMT -6. The time now is 02:05 PM.