Forum: Dyno Room
04-22-2008, 07:07 AM
|
Replies: 20
Views: 14,135
|
Forum: Dyno Room
04-07-2008, 12:21 PM
|
Replies: 70
Views: 31,334
|
Forum: Project Cars
03-24-2008, 09:39 PM
|
Replies: 294
Views: 73,336
|
Forum: Ford Pushrod Tech (5.0 & 5.8)
03-24-2008, 07:39 PM
|
Replies: 19
Views: 4,237
Gearwrench sets for cheap
Sears has a bunch of gearwrench sets for like 2 and 8 dollars.
go to sears.com and in the search thing type in 60239 as well as 60214
|
Forum: Ford Pushrod Tech (5.0 & 5.8)
03-03-2008, 10:14 PM
|
Replies: 61
Views: 5,427
|
Forum: Ford Pushrod Tech (5.0 & 5.8)
03-03-2008, 08:28 PM
|
Replies: 61
Views: 5,427
i had a 3550 and they are the best way better...
i had a 3550 and they are the best way better than the new 600. and it does have a 31 spline to the drive shaft. i have seen merley 500rwhp brreak a 600. everybody that i no will not run the 600 and...
|
Forum: Product Review
02-13-2008, 09:29 PM
|
Replies: 38
Views: 18,885
|
Forum: Mod Motor Tech (4.6 & 5.4)
02-07-2008, 10:14 PM
|
Replies: 13
Views: 4,626
|
Forum: Mod Motor Tech (4.6 & 5.4)
02-07-2008, 07:09 AM
|
Replies: 13
Views: 4,626
Blake can get a car very close with out using a...
Blake can get a car very close with out using a chip. as far as doug he is horrible, he no longer tunes at walker dyno. if i were you i would give ron willis a call he is probaly the best in town....
|
Forum: Ford Pushrod Tech (5.0 & 5.8)
02-01-2008, 10:18 AM
|
Replies: 29
Views: 2,602
|
Forum: Ford Pushrod Tech (5.0 & 5.8)
01-31-2008, 11:47 PM
|
Replies: 29
Views: 2,602
|
Forum: Ford Pushrod Tech (5.0 & 5.8)
01-31-2008, 05:34 PM
|
Replies: 29
Views: 2,602
well after what is's and maybes the culpret has...
well after what is's and maybes the culpret has identified himself. the two back mians were out of alighnment causing these two mains to lose oil pressure(would explain low pressure at idle). looks...
|
Forum: Ford Pushrod Tech (5.0 & 5.8)
01-30-2008, 03:36 PM
|
Replies: 29
Views: 2,602
my block is at the machine shop getting honed....
my block is at the machine shop getting honed. the cylinders looked great just no cross hatching. as far as the building of my engine the clearences were checked twice. the oil pump just went bad....
|
Forum: Ford Pushrod Tech (5.0 & 5.8)
01-30-2008, 12:26 PM
|
Replies: 29
Views: 2,602
well i do have a 7 quart pan and i have always...
well i do have a 7 quart pan and i have always used a high volume pump. as for loss of power i dunno the car makes plenty of power. made 550rwhp through a c4. there were no scratches in the cylinder...
|
Forum: Ford Pushrod Tech (5.0 & 5.8)
01-29-2008, 11:56 PM
|
Replies: 29
Views: 2,602
the pump driveshaft is not bent it is a arp...
the pump driveshaft is not bent it is a arp driveshaft. i am pretty sure the oil pumpwent bad probally why low oil pressure. well got the news from machine shop and the crank just needs to be...
|
Forum: Ford Pushrod Tech (5.0 & 5.8)
01-28-2008, 07:27 PM
|
Replies: 29
Views: 2,602
Bad Bad news from my 306
Well i probaly should have posted this earlier but i didnt. last weekend went home and pulled my engine out of our 86, took the oil pan off to change oil pump(kinda low oil pressure 14 lbs at idle)...
|
Forum: Chassis, Drivetrain, Suspension, Brakes & Tires
01-15-2008, 10:58 PM
|
Replies: 22
Views: 2,377
|