95 Mustang Cam help

Gear_Head15 · 07-07-2008, 01:53 PM

I am new here, i am thinking about buying a 95 mustang gt Here are the mods it has trickflow upper and lower intake,65mm tb,mass air,24lb injectors,walbro 255 fuel pump,high torque starter,200 amp high output alternator,3.73 posi rear end,lowered 1in., ac and heat work perfect! no cats,3in x-pipe,flows dumped,mil eliminators,496 lift cam,roller rockers,short throw shifter,underdrive pulley's along with new parts like a Aluminum radiator,high flow water pump,alternator 200 amp,high torque starter,msd ignition coil,wires,plugs,cap,rotor,fuel pump,fuel filter,belt,all hoses.

Now much bigger is the 496 lift can than stock and having no cats will it pass emissions without them or will i have to install cats? Also will it guzzle gas?

QWKSNKE · 07-07-2008, 02:46 PM

Stock cam is around .444 lift if I remember correctly.

On your smog question:
1)Need more specs on the cam to determine if it is smog friendly.
2) I don't live in an emissions required state but I am pretty sure the fact you have no cats on the x-pipe is going to cause it to fail

Gear_Head15 · 07-07-2008, 02:56 PM

i can tell you that the cam is close to the 5.0 cobra cam. Does that help?

Gear_Head15 · 07-07-2008, 02:57 PM

Quote:

Originally Posted by QWKSNKE

Stock cam is around .444 lift if I remember correctly.

On your smog question:
1)Need more specs on the cam to determine if it is smog friendly.
2) I don't live in an emissions required state but I am pretty sure the fact you have no cats on the x-pipe is going to cause it to fail

Also, how much power would that motor put out about?

coupe · 07-07-2008, 03:39 PM

Quote:

Originally Posted by Gear_Head15

lso, how much power would that motor put out about?

Power is hard to say1... Depends alot on the tuneup and the rest of those cam specs.

NMRA Pure street (max 310cid) cams are limited to .500 lift and those motors make well over 400hp at the tires.

BAD INT · 07-07-2008, 04:10 PM

stock cam .444 @ 266dur

Craig K. · 07-07-2008, 04:23 PM

I believe the 5.0 cobra cam has slightly smaller lift, but uses the 1.7 roller rocker to make it overall higher than the .444

EHardy1971 · 07-07-2008, 08:18 PM

.496 lift?,any idea who the cam is made by?

Also,like Coupe said,hard to say on the power without knowing the duration,and LSA of the cam as well.

QWKSNKE · 07-08-2008, 05:22 PM

Quote:

Originally Posted by Craig K.

I believe the 5.0 cobra cam has slightly smaller lift, but uses the 1.7 roller rocker to make it overall higher than the .444

yep. Cobra cams are .480 lift with the 1.7 rockers

94five0 · 07-08-2008, 06:27 PM

emissions?

whats that?

07-07-2008, 01:53 PM	#1
Gear_Head15 Junior Member Join Date: Jul 2008 Posts: 5	95 Mustang Cam help I am new here, i am thinking about buying a 95 mustang gt Here are the mods it has trickflow upper and lower intake,65mm tb,mass air,24lb injectors,walbro 255 fuel pump,high torque starter,200 amp high output alternator,3.73 posi rear end,lowered 1in., ac and heat work perfect! no cats,3in x-pipe,flows dumped,mil eliminators,496 lift cam,roller rockers,short throw shifter,underdrive pulley's along with new parts like a Aluminum radiator,high flow water pump,alternator 200 amp,high torque starter,msd ignition coil,wires,plugs,cap,rotor,fuel pump,fuel filter,belt,all hoses. Now much bigger is the 496 lift can than stock and having no cats will it pass emissions without them or will i have to install cats? Also will it guzzle gas?

07-07-2008, 02:46 PM	#2
QWKSNKE 3v's are slow Join Date: Dec 2004 Location: Here and There Posts: 17,152	Stock cam is around .444 lift if I remember correctly. On your smog question: 1)Need more specs on the cam to determine if it is smog friendly. 2) I don't live in an emissions required state but I am pretty sure the fact you have no cats on the x-pipe is going to cause it to fail __________________ 2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy

07-07-2008, 04:23 PM	#7
Craig K. Nothing new here Join Date: Dec 2004 Location: Senoia, GA Posts: 2,990	I believe the 5.0 cobra cam has slightly smaller lift, but uses the 1.7 roller rocker to make it overall higher than the .444 __________________ 1974 Triumph TR6 1985 Monte Carlo SS 1986 Mustang GT 2011 KIA Optima GTS

07-07-2008, 08:18 PM	#8
EHardy1971 Trunk Monkey Join Date: Jun 2007 Location: Home Posts: 5,708	.496 lift?,any idea who the cam is made by? Also,like Coupe said,hard to say on the power without knowing the duration,and LSA of the cam as well. __________________ Eric 89 LX Coupe-Juiced 01 Lightning-Boost 06 TBSS Last edited by EHardy1971; 07-07-2008 at 08:22 PM.

07-08-2008, 06:27 PM	#10
94five0 S-6 Mafia Join Date: Dec 2004 Location: above a bowling alley and below another bowling alley. Posts: 1,670	emissions? whats that? __________________ Jason ATF should be a store...not a government agency.

07-07-2008, 02:56 PM	#3
Gear_Head15 Junior Member Join Date: Jul 2008 Posts: 5	i can tell you that the cam is close to the 5.0 cobra cam. Does that help?

07-07-2008, 04:10 PM	#6
BAD INT Senior Member Join Date: Oct 2007 Posts: 184	stock cam .444 @ 266dur