TrickFlow head Q's

banditmwp · 01-29-2008, 05:12 PM

I read on their website that the trickflow twisted wedge street heads (with 2.02/1.60 valves and .540" springs) will work with stock bottom end but require different length pushrods. Anyone happen to know what length or am I gonna have to measure and wait to order them?

I seem to remember hearing 6.750" from one of my customers but not sure if that's right or not.

Also, any other head suggestions? I am looking to spend around $2k on heads, rockers, and some other miscellani (MAF, injectors, AFPR, MSD). I will be running an E-cam for now and a trick flow track heat intake.

Thanks for the advice

QWKSNKE · 01-29-2008, 06:00 PM

I think you are correct on 6.750 but I would call them to verify

BAD INT · 01-30-2008, 01:16 AM

you can run several letter cams with those heads and stock bottom end
b with 1.7's or f with 1.6's worst case run an eek.

qkjuicedpony · 01-30-2008, 05:15 AM

when you call Trick Flow.they will tell you which ones you need.

I would do a b cam and 1.7's though.

Wickd GT · 01-30-2008, 05:50 AM

6.70" will be fine, thats the ones I had on my stock block and R302 block. Best combination will be B cam with 1.72 roller rockers, it will give a
.516 lift, and pull real hard.

Edgar

Italian LX · 01-30-2008, 06:34 AM

I just so happen to have a good set of Trickflow hardened 6.700 pushrods that I'll sell you.

banditmwp · 01-30-2008, 05:30 PM

Quote:

Originally Posted by Italian LX

I just so happen to have a good set of Trickflow hardened 6.700 pushrods that I'll sell you.

how much?

01-29-2008, 05:12 PM	#1
banditmwp Welcome to America! Join Date: Dec 2004 Location: in the 11's Posts: 4,501	TrickFlow head Q's I read on their website that the trickflow twisted wedge street heads (with 2.02/1.60 valves and .540" springs) will work with stock bottom end but require different length pushrods. Anyone happen to know what length or am I gonna have to measure and wait to order them? I seem to remember hearing 6.750" from one of my customers but not sure if that's right or not. Also, any other head suggestions? I am looking to spend around $2k on heads, rockers, and some other miscellani (MAF, injectors, AFPR, MSD). I will be running an E-cam for now and a trick flow track heat intake. Thanks for the advice __________________ 91 GT Convertible 2006 Nissan Titan LE Crew Cab 2014 Peterbilt 337/Marion 22' box

01-29-2008, 06:00 PM	#2
QWKSNKE 3v's are slow Join Date: Dec 2004 Location: Here and There Posts: 17,152	I think you are correct on 6.750 but I would call them to verify __________________ 2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy

01-30-2008, 05:15 AM	#4
qkjuicedpony Dayuuuuuuum!!!!! Join Date: Dec 2004 Location: Dallas GA Posts: 2,933	when you call Trick Flow.they will tell you which ones you need. I would do a b cam and 1.7's though. __________________ 86 Mustang Gt......Mods piling up in my garage. 07 F350 dooly.....Tows my fifth wheel

01-30-2008, 06:34 AM	#6
Italian LX Daddy x4 ...we're done Join Date: Dec 2004 Location: Oxford, AL Posts: 11,551	I just so happen to have a good set of Trickflow hardened 6.700 pushrods that I'll sell you. __________________ -Brian '86 Mustang GT Convertible '88 Mustang LX coupe '11 Odyssey TE '21 Insight Touring

01-30-2008, 01:16 AM	#3
BAD INT Senior Member Join Date: Oct 2007 Posts: 184	you can run several letter cams with those heads and stock bottom end b with 1.7's or f with 1.6's worst case run an eek.

01-30-2008, 05:50 AM	#5
Wickd GT Friends Join Date: Dec 2004 Posts: 1,645	6.70" will be fine, thats the ones I had on my stock block and R302 block. Best combination will be B cam with 1.72 roller rockers, it will give a .516 lift, and pull real hard. Edgar