01-27-2006, 11:02 PM | #1 |
Super Moderator
Join Date: Dec 2004
Location: on the water
Posts: 1,280
|
Tweecer Pros
Need help here, I am using a CBAZA strategy on my 95 GT, had a pro m 75mm cal'd for 30#er's, 30#er's in the car but had no flow sheet on the MAF. Every now and then I would get some extremely high MAFV readings. Installed a new Pro-M 80mm cal'd for 30's and typed in the data in the caledit and I am still getting extremely high MAFV's like in the 300,000 range. This is the only bogus datalog number I am getting, all the other are looking correct. Me and Lee and Italian are at wits end on this.
__________________
2012 Jeep Wrangler Unlimited--- too many mods to list, about to be sitting on 1 ton axles. 2000 Ford F-350 Dually Lariat LE Crew Cab Short Box 7.3 auto 168,000 miles |
01-28-2006, 01:35 PM | #2 |
Senior Member
Join Date: May 2005
Posts: 290
|
Re: Tweecer Pros
During the DL you are showing MAFV in the 300,000 range?? That would point to either a bad ECU, bad TwEECer or maybe just a bad connection between teh EEC and TwEECer. Everything else seem OK on the car? Does it run OK? Anything else look wierd at the point where the MAFV fgoes crazy?
|
01-28-2006, 03:04 PM | #3 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Re: Tweecer Pros
If I understood him correctly last night on the phone, the car will not run with the stock tune, 30# scalar change, plus maf data from Pro-m.
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
01-28-2006, 03:07 PM | #4 | |
Daddy x4 ...we're done
Join Date: Dec 2004
Location: Oxford, AL
Posts: 11,551
|
Re: Tweecer Pros
Quote:
__________________
-Brian '86 Mustang GT Convertible '88 Mustang LX coupe '11 Odyssey TE '21 Insight Touring |
|
01-28-2006, 06:22 PM | #5 |
Super Moderator
Join Date: Dec 2004
Location: on the water
Posts: 1,280
|
Re: Tweecer Pros
Well took the computer apart and cleaned the contacts real good, still gave me high reading, now the tweecer will not write gives me a "null Read" window.
__________________
2012 Jeep Wrangler Unlimited--- too many mods to list, about to be sitting on 1 ton axles. 2000 Ford F-350 Dually Lariat LE Crew Cab Short Box 7.3 auto 168,000 miles |
02-01-2006, 02:31 PM | #6 |
5.0 Block/Walnut Cracker
Join Date: May 2005
Location: Working....
Posts: 2,409
|
Re: Tweecer Pros
If you are absolutely sure that the connections are clean, then check to make sure that the TwEECer is not pushed to far or not pushed far enough onto the EEC J3 port. Some of the TwEECers have a different style connector that works with the later model EEC-V's and when plugged in to the '88-'95 cars they normally would push in to far. IF this is the case you can make a
spacer out of cardboard etc. to space it out about 1/4" from the EEC case. If it is not this then I would say that you have a bad connection, bad TwEECer or bad PCM.
__________________
'14 Dodge Challenger SRT8 392 6-speed |
02-02-2006, 12:13 AM | #7 |
Member
Join Date: Mar 2005
Location: Sacramento California
Posts: 449
|
Re: Tweecer Pros
I have seen on a couple of PCMs where the traces are not complete, meaning that there is a break in the solder run from the J3 connector and the rest of the ciricut. This was on an A9T and a EX1.
I would first try what Dale said first.
__________________
EEC Analyzer A9M, TwEECer, 306ci, 73mm C&L w Tuner Tube, Cobra Intake, 42# inj, Edelbrock 6037, E303 cam, 155 fuel pump, FPR, 70mm TB, E-Fan, 3.55 gears, Powerdyne 9psi actual 5psi...way more. |
02-02-2006, 09:03 AM | #8 | |
5.0 Block/Walnut Cracker
Join Date: May 2005
Location: Working....
Posts: 2,409
|
Re: Tweecer Pros
Here is one Mike Glovers older posts that I ran across that goes with the above....
Quote:
__________________
'14 Dodge Challenger SRT8 392 6-speed |
|
02-03-2006, 06:43 PM | #9 |
Super Moderator
Join Date: Dec 2004
Location: on the water
Posts: 1,280
|
Re: Tweecer Pros
I got it to work finally, had to remove the computer from the stock location and leave it in the floor. Also Italian told me about the maf conversion in caledit not saving the right voltages when you save a MAF and told me to enter the points in eec analyzer to get a correct curve to save.
Problem now is that when I first start the car it sounds like it has a miss until it get warmed up, then runs fine but shut car off and crank it back up it hunts for idle and tries to die.
__________________
2012 Jeep Wrangler Unlimited--- too many mods to list, about to be sitting on 1 ton axles. 2000 Ford F-350 Dually Lariat LE Crew Cab Short Box 7.3 auto 168,000 miles |
02-03-2006, 08:44 PM | #10 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Re: Tweecer Pros
its to rich in open loop
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
|
|