|
08-13-2015, 04:51 PM | #1 |
Senior Member
Join Date: Jan 2008
Location: sand mountain
Posts: 463
|
terminator in a fox
Was just wondering if anyone here has made the swap and how hard the it is. Also the wiring how difficult is it. I'm just curious about this . Any info or links would be great thanks
__________________
1990 lx 302 w/trickflow intake, b-303 cam, tremec 3550 ,spec stage 3 clutch, crane 1.7 rockers, under drive pulleys, bbk full length headers, and x-pipe,3:73 gear. AND....... |
08-14-2015, 12:22 AM | #2 |
Halfshaft Killer
Join Date: Mar 2005
Location: The Kingdom
Posts: 3,910
|
The install is straight forward. The wiring isn't to bad if your if your decent with car wiring and reading the wiring schematics. Get the gauges to work is the hardest part imo. A coyote swap is a better swap to me. Just alittle more expensive and the same power n/a.
__________________
03 Cobra 06 F250 (\__/) (='.'=) (")_(") |
08-14-2015, 08:04 AM | #3 |
Senior Member
Join Date: Jan 2008
Location: sand mountain
Posts: 463
|
Well I know I can get everything I need for the terminator swap for around $10k. How much more would the coyote swap be? I've looked at the crate motors but they don't come with transmissions or wiring
__________________
1990 lx 302 w/trickflow intake, b-303 cam, tremec 3550 ,spec stage 3 clutch, crane 1.7 rockers, under drive pulleys, bbk full length headers, and x-pipe,3:73 gear. AND....... Last edited by blue90lx; 08-14-2015 at 08:07 AM. |
08-14-2015, 10:47 AM | #4 |
Friends
Join Date: Dec 2004
Location: Tempe Arizona
Posts: 3,029
|
just a quick search I found this: look on down the page for manual trans options http://www.hotrodpowersource.com/for...lpackages.html
__________________
2020 Range Rover Sport HSE P525 Dynamic - Firenze Red - Supercharged 5.0 - 518 HP SOLD - 2010 Camaro SS [/B] - Featured in GM High Tech Performance and Camaro Now Magazines - http://www.superchevy.com/features/g...of-perfection/ |
08-14-2015, 01:25 PM | #5 |
Senior Member
Join Date: Jan 2008
Location: sand mountain
Posts: 463
|
Thanks ez speed that's a very helpful site thanks
__________________
1990 lx 302 w/trickflow intake, b-303 cam, tremec 3550 ,spec stage 3 clutch, crane 1.7 rockers, under drive pulleys, bbk full length headers, and x-pipe,3:73 gear. AND....... |
08-14-2015, 04:09 PM | #6 |
Halfshaft Killer
Join Date: Mar 2005
Location: The Kingdom
Posts: 3,910
|
You can run any trans that would bolt up to a 4.6. If you go auto, you will have to have a mvb or some type of standalone controller for the trans. I'm running a 4r75 with a mvb on my coyote swap.
__________________
03 Cobra 06 F250 (\__/) (='.'=) (")_(") |
08-14-2015, 04:09 PM | #7 |
Halfshaft Killer
Join Date: Mar 2005
Location: The Kingdom
Posts: 3,910
|
Also you can get a motor from the f150 for around $2500 used. They have alittle less compression and different cams than the mustang motor.
__________________
03 Cobra 06 F250 (\__/) (='.'=) (")_(") |
08-15-2015, 09:36 PM | #8 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Thinking of doing a termi in the svo?
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
08-16-2015, 10:42 AM | #9 |
Senior Member
Join Date: Jan 2008
Location: sand mountain
Posts: 463
|
No I've been out of work due to health problems and been really bored reading up on a lot of different things
__________________
1990 lx 302 w/trickflow intake, b-303 cam, tremec 3550 ,spec stage 3 clutch, crane 1.7 rockers, under drive pulleys, bbk full length headers, and x-pipe,3:73 gear. AND....... |
Thread Tools | |
Display Modes | |
|
|