|
06-05-2008, 01:16 AM
|
#1 |
|
Senior Member
Join Date: Jan 2008
Location: sand mountain
Posts: 463
|
Torque box kit
I have a upper and lower torque box kit from upr. I know that the rear seat and the rearend and all that has to come out. My ? is how hard is it to install these? Do you guys recommend welding both upper and lowers or just the uppers? Any feed back would be great. Thanks
__________________
1990 lx 302 w/trickflow intake, b-303 cam, tremec 3550 ,spec stage 3 clutch, crane 1.7 rockers, under drive pulleys, bbk full length headers, and x-pipe,3:73 gear. AND....... 
|
|
|
|
06-05-2008, 03:40 AM
|
#2 |
|
Senior Member
Join Date: Apr 2005
Posts: 895
|
welded it alll
|
|
|
|
|
06-05-2008, 03:21 PM
|
#3 | |
|
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Quote:
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP  2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
|
|
|
|
|
06-05-2008, 04:35 PM
|
#4 |
|
Senior Member
Join Date: Dec 2006
Location: Birmingham
Posts: 168
|
most people just weld up all the seams on the factory brackets etc where it was just tac welded from the factory and then put some reinforcement plates on the lowers
|
|
|
|
|
06-10-2008, 07:32 AM
|
#5 |
|
Super Moderator
Join Date: Dec 2004
Location: on the water
Posts: 1,280
|
I have the UPR kit and I welded up everything.
__________________
2012 Jeep Wrangler Unlimited--- too many mods to list, about to be sitting on 1 ton axles. 2000 Ford F-350 Dually Lariat LE Crew Cab Short Box 7.3 auto 168,000 miles |
|
|
|
|
06-10-2008, 03:54 PM
|
#6 | |
|
I got a good sugar moma
Join Date: Dec 2005
Location: ON THE ROAD
Posts: 1,196
|
Quote:
Same here, if there was a spot to weld I welded it all.
__________________
Bottled 89 Coupe
|
|
|
|
|
|
06-15-2008, 08:30 AM
|
#7 |
|
Senior Member
Join Date: May 2005
Location: ALBERTVILLE, AL
Posts: 498
|
We installed these yesterday. Welding up the lowers in that small ass hole they fit in is going to be a bitch!
|
|
|
|
|
06-15-2008, 08:57 PM
|
#8 | |
|
I got a good sugar moma
Join Date: Dec 2005
Location: ON THE ROAD
Posts: 1,196
|
Quote:
Let me say YYYYYYYEEESSSSSSSS it was 
__________________
Bottled 89 Coupe
|
|
|
|
|
|
06-15-2008, 09:15 PM
|
#9 |
|
Senior Member
Join Date: Jan 2008
Location: sand mountain
Posts: 463
|
yeah that was a fun job last set i'll be doin for a while
__________________
1990 lx 302 w/trickflow intake, b-303 cam, tremec 3550 ,spec stage 3 clutch, crane 1.7 rockers, under drive pulleys, bbk full length headers, and x-pipe,3:73 gear. AND.......
|
|
|
|
 |
|
|
Linear Mode
