07-05-2006, 11:56 AM | #1 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Turbo a/r trims.....
What's good? What's bad? Does the size play a big factor in what these numbers mean? (T62,T-70, T-76, etc)
|
07-05-2006, 07:29 PM | #2 |
Si vis pacem, para bellum
Join Date: Dec 2004
Location: Tick-Tock, Tick-Tock.......
Posts: 5,146
|
Re: Turbo a/r trims.....
Here's a good link Lee.....http://www.turbomustangs.com/turbotech/main.htm
|
07-06-2006, 04:10 PM | #3 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Re: Turbo a/r trims.....
that is a good site Brad
But it didn't really tell me what I wanted to know
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
07-06-2006, 08:35 PM | #4 | |
5.0 Block/Walnut Cracker
Join Date: May 2005
Location: Working....
Posts: 2,409
|
Re: Turbo a/r trims.....
Quote:
|
|
07-06-2006, 08:59 PM | #5 | |
pro-jackstand racer
|
Re: Turbo a/r trims.....
Quote:
---------------------------------------------------- The Turbine Housings The exhaust and compressor housings on turbo chargers use a "scroll" design. For example, the exhaust housing's scroll is where the exhaust gasses enter the housing and are directed at the turbine. It's basically a smooth, tubular chamber that surrounds the turbine with a slot all the way around that acts as a nozzle to direct the exhaust gasses at the turbine. It's called a scroll because it slowly gets smaller in diameter as a goes around the turbine. This pressurizes the gasses, forcing them out of the slot/nozzle at a fast rate. In turbo-terms, the scroll is measured by the cross-sectional area of the scroll's "tube" (A) and the distance from the center of the "tube" to the turbine shaft (R). The values by themselves are not meaningful to the user and for the most part, R does not change much for different housings, but by dividing R into A, you get the A/R ratio. So, the A/R ratio of the exhaust housing refers to the size and shape of the scroll that is cast into the housing. It basically determines how restrictive the housing will be, versus how quickly the turbine will spin up. A lower A/R ratio (smaller scroll area, A) results in a more restrictive housing. This restriction speeds up the exhaust gasses and increases the amount that the gasses will expand. It's the speed and expansion of the gasses that causes the turbine to spin. So with a low A/R ratio, the turbine will spin up quicker, but as engine output and rpms increase, the restriction of the housing begins to build up too much back pressure on the engine, which reduces performance. A good rule of thumb for when there is too much back pressure is when the pressure in the exhaust manifold is more the half of the pressure in the cylinder. So basically, a larger A/R ratio will improve your engine's top end, while losing some mid range power and increasing turbo lag. A smaller A/R ratio will help the bottom and mid-range, but may effect the top end. On the compressor side, the housing also features a scroll design, but it has the opposite function. The air leaving the compressor turbine has a lot of speed, but not much pressure. The scroll on the compressor housing starts small and gets larger as it approaches the compressor outlet. This collects the air and builds up air pressure. So, the compressor housing is designed to convert the speed-energy of the air coming off of the compressor turbine into pressure-energy, which is much more useful to an engine. The Compressor Turbine -------------------------------------------------------------------------- Long Read I know...but hopefully that explains a bit more |
|
07-07-2006, 06:32 AM | #6 | |
Si vis pacem, para bellum
Join Date: Dec 2004
Location: Tick-Tock, Tick-Tock.......
Posts: 5,146
|
Re: Turbo a/r trims.....
Quote:
Yeah Lee, I didn't look at the article too much. Just enough that I saw that it had definitions for A/R and thought it would reference it more than it did. |
|
07-07-2006, 10:53 PM | #7 |
Super Moderator
Join Date: Dec 2004
Posts: 6,313
|
Re: Turbo a/r trims.....
Trims and the T66, T70, T76 numbers are all different than the A/R number.
I'll show you the differences and what they cause on a couple turbos sometime Lee. Actually studying them a little tells the story way better than the article.
__________________
" If you can't explain it simply, you don't understand it well enough. " - Albert Einstein |
07-08-2006, 04:55 AM | #8 | |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Re: Turbo a/r trims.....
Quote:
In my original post I was asking if a good a/r was dependent on the actual size. Example, would a 70 a/r be better on a t-64 or a t70? |
|
|
|