07-07-2008, 01:53 PM | #1 |
Junior Member
Join Date: Jul 2008
Posts: 5
|
95 Mustang Cam help
I am new here, i am thinking about buying a 95 mustang gt Here are the mods it has trickflow upper and lower intake,65mm tb,mass air,24lb injectors,walbro 255 fuel pump,high torque starter,200 amp high output alternator,3.73 posi rear end,lowered 1in., ac and heat work perfect! no cats,3in x-pipe,flows dumped,mil eliminators,496 lift cam,roller rockers,short throw shifter,underdrive pulley's along with new parts like a Aluminum radiator,high flow water pump,alternator 200 amp,high torque starter,msd ignition coil,wires,plugs,cap,rotor,fuel pump,fuel filter,belt,all hoses.
Now much bigger is the 496 lift can than stock and having no cats will it pass emissions without them or will i have to install cats? Also will it guzzle gas? |
07-07-2008, 02:46 PM | #2 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Stock cam is around .444 lift if I remember correctly.
On your smog question: 1)Need more specs on the cam to determine if it is smog friendly. 2) I don't live in an emissions required state but I am pretty sure the fact you have no cats on the x-pipe is going to cause it to fail
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
07-07-2008, 02:56 PM | #3 |
Junior Member
Join Date: Jul 2008
Posts: 5
|
i can tell you that the cam is close to the 5.0 cobra cam. Does that help?
|
07-07-2008, 02:57 PM | #4 | |
Junior Member
Join Date: Jul 2008
Posts: 5
|
Quote:
Also, how much power would that motor put out about? |
|
07-07-2008, 03:39 PM | #5 | |
Super Moderator
Join Date: Dec 2004
Posts: 6,313
|
Quote:
NMRA Pure street (max 310cid) cams are limited to .500 lift and those motors make well over 400hp at the tires.
__________________
" If you can't explain it simply, you don't understand it well enough. " - Albert Einstein |
|
07-07-2008, 04:10 PM | #6 |
Senior Member
Join Date: Oct 2007
Posts: 184
|
stock cam .444 @ 266dur
|
07-07-2008, 04:23 PM | #7 |
Nothing new here
Join Date: Dec 2004
Location: Senoia, GA
Posts: 2,990
|
I believe the 5.0 cobra cam has slightly smaller lift, but uses the 1.7 roller rocker to make it overall higher than the .444
__________________
1974 Triumph TR6 1985 Monte Carlo SS 1986 Mustang GT 2011 KIA Optima GTS |
07-07-2008, 08:18 PM | #8 |
Trunk Monkey
Join Date: Jun 2007
Location: Home
Posts: 5,708
|
.496 lift?,any idea who the cam is made by? Also,like Coupe said,hard to say on the power without knowing the duration,and LSA of the cam as well.
__________________
Eric 89 LX Coupe-Juiced 01 Lightning-Boost 06 TBSS Last edited by EHardy1971; 07-07-2008 at 08:22 PM. |
07-08-2008, 05:22 PM | #9 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
yep. Cobra cams are .480 lift with the 1.7 rockers
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
07-08-2008, 06:27 PM | #10 |
S-6 Mafia
Join Date: Dec 2004
Location: above a bowling alley and below another bowling alley.
Posts: 1,670
|
emissions?
whats that?
__________________
Jason ATF should be a store...not a government agency. |
|
|