07-07-2007, 07:49 PM | #1 |
ADDICTED TO SMALL BLOCKS
Join Date: Jan 2007
Location: lookout mt
Posts: 1,757
|
need wisdom?
ok i am helping a buddy work out some bugs. got a dss 331 victor jr heads and intake comp 280 290 i beleive not quiet sure has 560 580 lift msd 6al new and new msd dizzy 750 promform dp comectic mls .100 head gaskets 1.7 rollers ok here it is engine cold is running fine after you turn it up or get warm setting at idle it will have a loud backfire in exhaust. i am thinking plug not dissipating heat good. something in dizzy or plug wire. or engine to frame ground bad.not so sure about these plugs they are the ones that have a flat plug to head seal not tapered they look small to. they are autolite 3924.I have never run the victor jr heads so I am not familiar with which plug and gap to use.any help would be greatly appreciated. thx ps i also have fixed all header leaks. what bugs me is just idlingit will do it. have also swapped carb off my gt which runs great
Last edited by waypastcrazy; 07-07-2007 at 07:54 PM. |
07-07-2007, 10:42 PM | #2 |
Super Moderator
Join Date: Dec 2004
Posts: 6,313
|
Maybe one of the holes not getting an equal fuel/air distribution? Is there a carb spacer being used? The plugs are the right number, They are a good heat range too, I don't think that's the problem, unless they're gapped like .060. They should be anywhere from .035-.045.
Check also to see that there's not a fuel line running near an exhaust. That might be causing fuel vapor lock at warm temps. And check pressure. Fuel pressure gauge will help you out.
__________________
" If you can't explain it simply, you don't understand it well enough. " - Albert Einstein |
07-07-2007, 10:53 PM | #3 | |
Nothing new here
Join Date: Dec 2004
Location: Senoia, GA
Posts: 2,990
|
Quote:
With the MSD he should be running a higher gap, or atleast I always did in the '85, I ran around 40-45 once and the engine ran like crap, open the gap to around 60 and it would rev real nice. Have you pulled the plug wires off and checked them with an ohm meter, and made sure all the ends are crimped well? What is the timing set at, is it high enough?
__________________
1974 Triumph TR6 1985 Monte Carlo SS 1986 Mustang GT 2011 KIA Optima GTS |
|
07-07-2007, 11:07 PM | #4 |
Super Moderator
Join Date: Dec 2004
Posts: 6,313
|
timing is a good idea. what type of advance on it? I know MSD and other high-energy spark systems allow more gap, but never really thought it a requirement. Some engines take different to things. Checking it out would not hurt.
__________________
" If you can't explain it simply, you don't understand it well enough. " - Albert Einstein |
07-07-2007, 11:47 PM | #5 |
I got a good sugar moma
Join Date: Dec 2005
Location: ON THE ROAD
Posts: 1,196
|
I run my gap at 35 with a full msd set up.
__________________
Bottled 89 Coupe |
07-08-2007, 05:59 AM | #6 |
Senior Member
Join Date: Jan 2006
Location: Looking for more ways to add BOOST
Posts: 167
|
Rotor phase, MSD says that their dis. are rotor phased from the factory,Not always true.
__________________
Hauling A** on Pump Gas !!!!! |
07-08-2007, 08:14 AM | #7 |
ADDICTED TO SMALL BLOCKS
Join Date: Jan 2007
Location: lookout mt
Posts: 1,757
|
no carb spacer. gap has been at .50 then now at .45 fuel line is away frome exhaust and already have pressure gauge.plug wire ohmed good and have played with timing already it is at 40 right now.it is amechanical advace. tried all the combonations of springs yesterday.rotor phase ok got my attention how do i check rotor phase?
|
07-08-2007, 08:39 AM | #8 |
ADDICTED TO SMALL BLOCKS
Join Date: Jan 2007
Location: lookout mt
Posts: 1,757
|
ps
the rotor is not the adjustable one do i need to get one to phase the rotor thx
|
07-08-2007, 11:53 AM | #9 |
Daddy x4 ...we're done
Join Date: Dec 2004
Location: Oxford, AL
Posts: 11,551
|
The 392x series of plugs comes with a gasket (metal tapered washer) that is required for proper sealing. It sounds like whomever put those plugs in may have just thrown them away. I suggest buyinh a new set and using the gaskets. The flat edge of those plugs will not seal properly without them.
__________________
-Brian '86 Mustang GT Convertible '88 Mustang LX coupe '11 Odyssey TE '21 Insight Touring |
07-08-2007, 12:15 PM | #10 |
ADDICTED TO SMALL BLOCKS
Join Date: Jan 2007
Location: lookout mt
Posts: 1,757
|
plugs
have already changed plugs and they do have the metal gaskets thx
|
|
|