My 850rwhp street car project??? - Page 5

rtusnake · 01-09-2009, 10:13 PM

Clear, but either would look good. I would change the tails out though if you do smoke in the front

klu408 · 01-11-2009, 12:10 AM

Thanks anybody else?

klu408 · 01-11-2009, 12:11 AM

I got my drilled and slotted rotors in the other day!!

I will have to post pics later..

blue90lx · 01-12-2009, 08:57 AM

I'd go with smoke man! They look gooooooood!

klu408 · 01-27-2009, 04:11 PM

Here are some pics of my progress!!

sccapri · 01-27-2009, 07:43 PM

Kelly, put some high temp paint on the rotors and it will keep the rust off of them. What else do you have left to do? Let me know when you head to the dyno, if I can make it I would like to go. Looks like things are coming along pretty good.

klu408 · 01-27-2009, 09:15 PM

Do they have it in clear? I like the look of them now? I have to finish my fuel system and all my wiring!!!

( I forgot to mention I HATE wiring)
As far as the dyno goes I'm going to buy a widebansd and tune as close as I can myself, then I may carry it to get fine tuned, Ive had too many $300 dyno bills!!!!!!!!

sccapri · 01-29-2009, 09:00 PM

You shouldn't have a whole lot of wiring to do with a carb. If the rotors aren't coated with something, pretty much anything that is not touched by the pads will get rust on them sooner or later.

Rcoupe91svo · 01-29-2009, 09:40 PM

I need a clean towel

klu408 · 02-14-2009, 08:14 PM

Finally got my axles in and roller it out of the shop and took some pics. I can't wait to hear this thin running!!!

01-09-2009, 10:13 PM	#41
rtusnake Halfshaft Killer Join Date: Mar 2005 Location: The Kingdom Posts: 3,910	Clear, but either would look good. I would change the tails out though if you do smoke in the front __________________ 03 Cobra 06 F250 (\__/) (='.'=) (")_(")

01-12-2009, 08:57 AM	#44
blue90lx Senior Member Join Date: Jan 2008 Location: sand mountain Posts: 463	I'd go with smoke man! They look gooooooood! __________________ 1990 lx 302 w/trickflow intake, b-303 cam, tremec 3550 ,spec stage 3 clutch, crane 1.7 rockers, under drive pulleys, bbk full length headers, and x-pipe,3:73 gear. AND.......

01-29-2009, 09:40 PM	#49
Rcoupe91svo Senior Member Join Date: Feb 2007 Location: Oxford AL. Posts: 631	I need a clean towel __________________ Brian 1991 Mustang coupe 2001 Mustang GT No boost .....No bottle ... All throttle

01-11-2009, 12:10 AM	#42
klu408 Senior Member Join Date: May 2008 Location: Sand Mountian Posts: 180	Thanks anybody else?

01-11-2009, 12:11 AM	#43
klu408 Senior Member Join Date: May 2008 Location: Sand Mountian Posts: 180	I got my drilled and slotted rotors in the other day!! I will have to post pics later..

01-27-2009, 04:11 PM	#45
klu408 Senior Member Join Date: May 2008 Location: Sand Mountian Posts: 180	Here are some pics of my progress!!

01-27-2009, 07:43 PM	#46
sccapri Junior Member Join Date: Dec 2008 Posts: 20	Kelly, put some high temp paint on the rotors and it will keep the rust off of them. What else do you have left to do? Let me know when you head to the dyno, if I can make it I would like to go. Looks like things are coming along pretty good.

01-27-2009, 09:15 PM	#47
klu408 Senior Member Join Date: May 2008 Location: Sand Mountian Posts: 180	Do they have it in clear? I like the look of them now? I have to finish my fuel system and all my wiring!!! ( I forgot to mention I HATE wiring) As far as the dyno goes I'm going to buy a widebansd and tune as close as I can myself, then I may carry it to get fine tuned, Ive had too many $300 dyno bills!!!!!!!!

01-29-2009, 09:00 PM	#48
sccapri Junior Member Join Date: Dec 2008 Posts: 20	You shouldn't have a whole lot of wiring to do with a carb. If the rotors aren't coated with something, pretty much anything that is not touched by the pads will get rust on them sooner or later.

02-14-2009, 08:14 PM	#50
klu408 Senior Member Join Date: May 2008 Location: Sand Mountian Posts: 180	Finally got my axles in and roller it out of the shop and took some pics. I can't wait to hear this thin running!!!