|
05-14-2008, 01:35 AM
|
#1 |
|
Senior Member
Join Date: Jan 2008
Location: sand mountain
Posts: 463
|
Which Brand Subframes To Use?
WHAT BRAND SUBFRAMES DO YOU GUYES RECOMMEND. I'VE LOOKED AT ALL KINDS JUST WONDERING WHAT YOU WOULD PUT ON YOUR CAR. LET ME KNOW.
__________________
1990 lx 302 w/trickflow intake, b-303 cam, tremec 3550 ,spec stage 3 clutch, crane 1.7 rockers, under drive pulleys, bbk full length headers, and x-pipe,3:73 gear. AND....... 
|
|
|
|
05-14-2008, 03:52 AM
|
#2 |
|
Member
Join Date: Dec 2006
Location: McCalla, Alabama
Posts: 30
 |
All in all they all do the same job, can not say one is better than the other. Although I have a set of BBK's on my car.In saying this I would buy the bolt-in's and then have a small Weld Beed run on both sides at both ends. Just make sure that when installing them that the car is sitting on all four's. Jack the car up and place ramps, blocks, or anything you can to sit the car down on without fear of it falling while doing the install.
|
|
|
|
|
05-14-2008, 06:36 AM
|
#3 |
|
Im gonna show her my...
Join Date: Dec 2004
Location: Somewhere providing FREE tech support.
Posts: 4,269
|
__________________
I heard it on the internet, so it must be true. "I believe that a person's moral compass can be determined by how he references free men the right to defend themselves." T. Nugent "An armed society is a polite society. Manners are good when one may have to back up his acts with his life." R. Heinlein "Never argue with an idiot. They drag you down to their level, then beat you with experience." -Unknown |
|
|
|
|
05-14-2008, 06:47 AM
|
#4 |
|
Senior Member
Join Date: Dec 2006
Location: Birmingham
Posts: 168
|
maximum motorsports full length
|
|
|
|
|
05-14-2008, 07:18 AM
|
#5 | |
|
Administrator
Join Date: Dec 2004
Location: Huntsville, AL
Posts: 14,774
|
Quote:
__________________
1998 Mustang GT Coupe - World's Slowest Racecar 2005 Toyota 4Runner SR5 V8 2013 Volkswagen Jetta Sportwagen TDI |
|
|
|
|
|
05-14-2008, 09:27 AM
|
#6 |
|
Dayuuuuuuum!!!!!
Join Date: Dec 2004
Location: Dallas GA
Posts: 2,933
|
Maximum Motorsports or Competition Engineering.
The Comp Eng ones have a plate that goes up and along the side of the torque boxes so you can add a little strength there too.
__________________
86 Mustang Gt......Mods piling up in my garage.
07 F350 dooly.....Tows my fifth wheel |
|
|
|
|
05-14-2008, 09:56 AM
|
#7 |
|
Friends
Join Date: Mar 2005
Location: McCalla
Posts: 1,241
|
If you can find them, Kenny Brown SFCs are good.
|
|
|
|
|
05-14-2008, 10:56 AM
|
#8 |
|
Senior Member
Join Date: Jan 2008
Location: sand mountain
Posts: 463
|
thanks, some people say just get any brand but i don't want to pay for something that's not worth it. Some have bigger gauge metal and some don't not looking for any crap or cheap sfc. Thanks for the links really leining toward the mm. thanks
__________________
1990 lx 302 w/trickflow intake, b-303 cam, tremec 3550 ,spec stage 3 clutch, crane 1.7 rockers, under drive pulleys, bbk full length headers, and x-pipe,3:73 gear. AND.......
|
|
|
|
|
05-14-2008, 08:40 PM
|
#9 |
|
Senior Member
Join Date: May 2005
Location: ALBERTVILLE, AL
Posts: 498
|
oh i see. ya dont like the ones i bought for my car huh? pay that high dollar for a piece of square metal !
|
|
|
|
|
05-15-2008, 11:06 AM
|
#10 |
|
Senior Member
Join Date: Dec 2006
Location: Birmingham
Posts: 168
|
i bet todd can actually make you some that would be stronger than any you will find mass produced though and for a competitive price
|
|
|
|
 |
|
|
Linear Mode
