02-13-2010, 09:04 PM | #11 | |
Junior Member
Join Date: Feb 2010
Location: Anniston,AL
Posts: 28
|
Quote:
yea i tithgten the hell outa them
__________________
89 Mustang GT 302 Cubic Inches Crane Cam Setup Holley 750 dbl Pump Whole Lota Gittyup |
|
02-13-2010, 09:12 PM | #12 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
where was the crack on the bell housing? Pretty sure that aluminum does not like to be welded. If it is in the general area of the starter, you may want to round another one up. I am sure somebody on here has one they could spare cheap
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
02-13-2010, 09:18 PM | #13 | |
Junior Member
Join Date: Feb 2010
Location: Anniston,AL
Posts: 28
|
Quote:
Nah, the crack was on the other side where the clutch cable goes through, but i dont get it im gonna try useing shim tomorrow if that dont work i dunno what else to do i guess ill jus sell it, its a BADASS car but jus this one problem ill try useing a shim tomorrow if that dont work ill look for a bellhouseing this is gonna suck if i gotta take the damn transmission out again i had it out 3 times already first time i put clutch in wrong then had to change pilot bearing then had to realign belhousing just my luck, right? hahaa
__________________
89 Mustang GT 302 Cubic Inches Crane Cam Setup Holley 750 dbl Pump Whole Lota Gittyup |
|
02-13-2010, 09:27 PM | #14 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Are both bellhousing dowel pins in place? There has to be something going on with the bellhousing if it still grinds after 3 starters and all teeth appear to be in good shape.
You could try shimming one of the starter bolts but I have never owned a Ford that required shimming. Definitely odd
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
02-13-2010, 09:34 PM | #15 | |
Junior Member
Join Date: Feb 2010
Location: Anniston,AL
Posts: 28
|
Quote:
BTW: On one of the other starters i put on this car it started up PERFECT i mean it had no grinding at all NONE! it started up like the car was brand new.... then 2 weeks later it started do this crap again.. any idea what might have caused that..? at first i thought the other starter i had just wouldnt turn it over cuz of the compression but i guess i was wrong
__________________
89 Mustang GT 302 Cubic Inches Crane Cam Setup Holley 750 dbl Pump Whole Lota Gittyup Last edited by 89StangRompt; 02-13-2010 at 09:36 PM. |
|
02-13-2010, 10:35 PM | #16 |
Mind Blowing
Join Date: Jun 2006
Location: Dawsonville Ga
Posts: 3,913
|
is it the right engine plate? has the hole been cut out any?
__________________
Slow Joe Racing 2008 dodge ram 5.7 HEMI 1993 lx with a 289 and a 3 speed on the floor WTB 1955 t-bird project |
02-13-2010, 10:37 PM | #17 |
Junior Member
Join Date: Feb 2010
Location: Anniston,AL
Posts: 28
|
no they aint been cut it fits in perfect
I have recently just figured it out.. what i thought was 3113 which didnt make since at all to me is acually E7TE which means its a 87 truck engine so i just ordered a ring gear to put on the the flywheel to get it going i made sure that this ring gear fits an 87 truck so i should be all set and all my problems are solved thanks again for your generosity!! thanks for all your posts on trying to help me i really appreciate it greatly A+ support, thanks alot. i have the totally wrong flywheel im an idiot lmao what can i say, people makes mistakes, thanks again guys i much appreciate it!!!!
__________________
89 Mustang GT 302 Cubic Inches Crane Cam Setup Holley 750 dbl Pump Whole Lota Gittyup Last edited by 89StangRompt; 02-14-2010 at 12:30 AM. |
02-14-2010, 01:52 PM | #18 | |
Trunk Monkey
Join Date: Jun 2007
Location: Home
Posts: 5,708
|
Quote:
__________________
Eric 89 LX Coupe-Juiced 01 Lightning-Boost 06 TBSS |
|
02-14-2010, 02:44 PM | #19 |
Junior Member
Join Date: Feb 2010
Location: Anniston,AL
Posts: 28
|
i TRYED regular mustang fly wheel it doesnt work either i gotten one for manual tran and manual trans start i dunno what to do then how am i supposed to find out what to get it E7TE reading decoding directions is 87 Truck Engine
EDIT: I canceled my order with the truck engine flywheel ring gear here is the one i got now i hope this does it for me http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product_Flywheel-Ring-Gear-Motormite_3923428-P_268_R|GRPTRANAMS_542475036___
__________________
89 Mustang GT 302 Cubic Inches Crane Cam Setup Holley 750 dbl Pump Whole Lota Gittyup Last edited by 89StangRompt; 02-14-2010 at 03:21 PM. |
02-14-2010, 04:00 PM | #20 |
Trunk Monkey
Join Date: Jun 2007
Location: Home
Posts: 5,708
|
Understood, but the H.O.'s also had E7TE heads, which were off the shelf truck heads. The particular casting # denotes what the part was originally intended for, but not the only vehicle it was used in. Ford is known for doing that. Just trying to save you a headache.
__________________
Eric 89 LX Coupe-Juiced 01 Lightning-Boost 06 TBSS |
|
|