12 Tooth Crank Trigger wheel for AEM

Dale McPeters · 07-31-2006, 03:53 AM

Well time for some more testing with the AEM unit.
Hope to be able to give this a try sometime this fall.
It is a 12 tooth crank trigger wheel setup like Mike at
toohighpsi.com used to sell. Finally found a guy in MN
that had a few that he had made so I bought two just
in case that I destroy one etc. etc.
Going to have to mill about 1/8" off of mounting ring of
dampner for it to work.
A few pictures......

SvoBrown · 07-31-2006, 04:45 AM

I have a 1,36 wheel that I am going to use on my next engine. On yours how does it know where tdc is? All the teeth look the same on you wheel.

QWKSNKE · 07-31-2006, 04:56 AM

I would guess by the degrees I see engraved on the shiny thing

Italian LX · 07-31-2006, 05:08 AM

Quote:

Originally Posted by QWKSNKE

I would guess by the degrees I see engraved on the shiny thing

He meant, how does the sensor know where TDC is.

QWKSNKE · 07-31-2006, 05:09 AM

oops

Dale McPeters · 07-31-2006, 06:25 AM

Quote:

Originally Posted by SvoBrown

I have a 1,36 wheel that I am going to use on my next engine. On yours how does it know where tdc is? All the teeth look the same on you wheel.

It references the cam sensor for tdc. It only uses the trigger wheel for
the pulse. By the way from what I have found so far the 30-1400 box should
be able to run an SVO 4 cylinder....

Quote:

Originally Posted by QWKSNKE

oops

07-31-2006, 03:53 AM	#1
Dale McPeters 5.0 Block/Walnut Cracker Join Date: May 2005 Location: Working.... Posts: 2,409	12 Tooth Crank Trigger wheel for AEM Well time for some more testing with the AEM unit. Hope to be able to give this a try sometime this fall. It is a 12 tooth crank trigger wheel setup like Mike at toohighpsi.com used to sell. Finally found a guy in MN that had a few that he had made so I bought two just in case that I destroy one etc. etc. Going to have to mill about 1/8" off of mounting ring of dampner for it to work. A few pictures...... Last edited by Dale McPeters; 08-14-2006 at 06:55 PM.

07-31-2006, 04:45 AM	#2
SvoBrown Senior Member Join Date: Nov 2005 Location: Graham AL Posts: 1,461	Re: 12 Tooth Crank Trigger wheel for AEM I have a 1,36 wheel that I am going to use on my next engine. On yours how does it know where tdc is? All the teeth look the same on you wheel.

07-31-2006, 04:56 AM	#3
QWKSNKE 3v's are slow Join Date: Dec 2004 Location: Here and There Posts: 17,152	Re: 12 Tooth Crank Trigger wheel for AEM I would guess by the degrees I see engraved on the shiny thing __________________ 2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy

07-31-2006, 05:09 AM	#5
QWKSNKE 3v's are slow Join Date: Dec 2004 Location: Here and There Posts: 17,152	Re: 12 Tooth Crank Trigger wheel for AEM oops __________________ 2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy