02-24-2007, 05:10 PM | #1 |
Mind Blowing
Join Date: Jun 2006
Location: Dawsonville Ga
Posts: 3,913
|
Brake help
We are working on a 91 LX with a 429 in it. We went with a manual brake master cylider.It still has the stock 4cyl brakes up front, that will change!It has the thunderbird turbocoupe rears that are disk.We need to know how to get some good brakes on this thing bad.But it has to stay with a small master cylider because of the BBF.
__________________
Slow Joe Racing 2008 dodge ram 5.7 HEMI 1993 lx with a 289 and a 3 speed on the floor WTB 1955 t-bird project Last edited by SlowJoe; 02-24-2007 at 05:30 PM. |
02-24-2007, 05:23 PM | #2 |
Senior Member
Join Date: Nov 2005
Location: Graham AL
Posts: 1,461
|
Booster should be ok, just need a bigger master cylider. The bore sizes is larger on the disc brake mustang compared to the drum one. One out of a svo would be just right. You need the valve thing for it to. What is it call.
Autozone is a cheap place to get one and new. I have a brake booster off and explorer that barly fit with new holes and alittle hammer work. Smooth brake with half the foot.
__________________
''Life's tough... it's even tougher if you're stupid.'' - - John Wayne Last edited by SvoBrown; 02-24-2007 at 05:29 PM. |
02-24-2007, 05:28 PM | #3 |
Mind Blowing
Join Date: Jun 2006
Location: Dawsonville Ga
Posts: 3,913
|
Can't run a booster, it hits the valve cover.And i know the valve You are talking about.It starts with a P i think.lol
I edited my first post sorry
__________________
Slow Joe Racing 2008 dodge ram 5.7 HEMI 1993 lx with a 289 and a 3 speed on the floor WTB 1955 t-bird project |
02-24-2007, 05:31 PM | #4 |
Senior Member
Join Date: Nov 2005
Location: Graham AL
Posts: 1,461
|
Pinto?
__________________
''Life's tough... it's even tougher if you're stupid.'' - - John Wayne |
02-24-2007, 05:53 PM | #5 |
Mind Blowing
Join Date: Jun 2006
Location: Dawsonville Ga
Posts: 3,913
|
pinto what?
__________________
Slow Joe Racing 2008 dodge ram 5.7 HEMI 1993 lx with a 289 and a 3 speed on the floor WTB 1955 t-bird project |
02-24-2007, 06:56 PM | #6 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
proportioning valve
|
02-24-2007, 07:25 PM | #7 |
Mind Blowing
Join Date: Jun 2006
Location: Dawsonville Ga
Posts: 3,913
|
yea thats it.i need a pinto?
__________________
Slow Joe Racing 2008 dodge ram 5.7 HEMI 1993 lx with a 289 and a 3 speed on the floor WTB 1955 t-bird project |
02-24-2007, 07:35 PM | #8 |
Senior Member
Join Date: Nov 2005
Location: Graham AL
Posts: 1,461
|
Look for a pinto master brake cylinder. They may be small enough to fit your tight spot.
__________________
''Life's tough... it's even tougher if you're stupid.'' - - John Wayne |
02-25-2007, 07:14 AM | #9 |
Nothing new here
Join Date: Dec 2004
Location: Senoia, GA
Posts: 2,990
|
You could try and run an SVO M/C however because the piston bore is so large, it may not fit the manual M/C adaptor plate.
This is the problem I ran into years ago, however I was using a Ford manual M/C plate, not an aftermarket one. Secondly, since the bore size of the SVO M/C is so large, pedal effort might be very high, not sure. Also what front brakes are you planning on running? The caliper piston bore size and amount of fluid you will be trying to move really dictates how big your M/C bore size must be. I suggest you guys figure out what fron calipers / rotors you want to use, then go from there.
__________________
1974 Triumph TR6 1985 Monte Carlo SS 1986 Mustang GT 2011 KIA Optima GTS |
02-25-2007, 08:15 AM | #10 |
Mind Blowing
Join Date: Jun 2006
Location: Dawsonville Ga
Posts: 3,913
|
we are planing on putting the gt front brakes on it.
__________________
Slow Joe Racing 2008 dodge ram 5.7 HEMI 1993 lx with a 289 and a 3 speed on the floor WTB 1955 t-bird project |
|
|