09-12-2012, 07:00 PM | #161 |
Crusin...
Join Date: Feb 2005
Location: Various Places in Middle AL
Posts: 3,542
|
__________________
Liberal education has nothing to do with liberal or conservative politics. Liberal education is the simple idea of a broad and well-rounded course of study in the humanities, social sciences, sciences, and the arts. The overarching goal is to liberate the mind from ignorance and superstition. |
09-12-2012, 07:00 PM | #162 |
pro-jackstand racer
|
still need to drop trans and replace what I believe is a leaking seal on the reverse piston, still no reverse!!! ARGHHH....
__________________
And God created Neil Peart so that lightning would make sense to the world.
~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
09-14-2012, 07:33 PM | #163 |
pro-jackstand racer
|
got the trans out this evening and got it torn down to the point where I could get reverse drum out and take that piston out, I also went ahead and got a new reverse servo piston too just to be sure...Just waiting till monday or tuesday to get that back together (my buddy in Columbus has the seal installer for the pistons)
__________________
And God created Neil Peart so that lightning would make sense to the world.
~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
09-15-2012, 12:18 AM | #164 |
Halfshaft Killer
Join Date: Mar 2005
Location: The Kingdom
Posts: 3,910
|
Monday or tuesday? You have the whole weekend lol. Hopefully everything goes back together smooth
__________________
03 Cobra 06 F250 (\__/) (='.'=) (")_(") |
09-17-2012, 06:22 PM | #165 |
pro-jackstand racer
|
HAHA, ya, we were out of town this weekend. I actually found out WHY I didn't have reverse...and this little nugget of knowledge is FREE....I changed from a cast reverse drum to the STAMPED steel reverse drum and Mechanical Diode (ratcheting one way clutch) with 2 inch overdrive band....
Well, at any rate, I was researching WTF was going on with no reverse and realize that the cast reverse drum requires a reverse piston with the casting numbers beginning with RF-E0 cast numbers, the stamped drums use RF-E9 or F0 cast numbers. So I run down to the garage and LO AND BEHOLD...I've got the cast reverse piston in my STAMPED reverse drum. NO BUENO!!! So I have the new piston with new seals ready to go as soon as I can get the seal installer tools from my buddy in Columbus tomorrow!!! Hopefully I'll have this trans back in there in the next day or so.
__________________
And God created Neil Peart so that lightning would make sense to the world.
~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
10-10-2012, 06:11 PM | #166 |
pro-jackstand racer
|
Well trans was in and out 2 MORE times, got new pump, different valvebody, 2 different reverse servo pistons (first one would not aircheck), another set of intermediate clutches AND steels (clearances were off), and completely torn apart and air checked and FINALLY I have reverse..LOL
I took it out for a spin the other day and the tune leaves a little bit to be desired (my own doing) but I've got a chip in it for now just to move it around. I've got a tubular k-member and some new springs for coil-overs. In addition I may be changing some interior changes (different seats, entire center console from mustang and black mustang dash)
__________________
And God created Neil Peart so that lightning would make sense to the world.
~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
10-10-2012, 10:01 PM | #167 |
Halfshaft Killer
Join Date: Mar 2005
Location: The Kingdom
Posts: 3,910
|
Getting close
__________________
03 Cobra 06 F250 (\__/) (='.'=) (")_(") |
10-11-2012, 05:11 PM | #168 |
pro-jackstand racer
|
yup, I'm getting another oilpan from a buddy since mine is leaking BADLY from the turbo oil drain (-10), and swapping it in when I change to the Tubular K member...I can't wait to get it going FOR REAL!!!
Bad thing is with my work (landscaping) winding down, I'll have more time...but no $$$ LOL Dammit MAN!
__________________
And God created Neil Peart so that lightning would make sense to the world.
~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
11-02-2012, 07:54 PM | #169 |
pro-jackstand racer
|
Oilpan is fixed, tubular K-member is in, swapped the spacers around on my coilovers so I can get some more travel out of them (thinking they were bottoming out the way I had the spacers set), need to put bumpsteer kit on and then get some "freshened up" calipers on there. Got my new direct drum for trans in the other day and just waiting on the Alto red's and kolene steel kit to come in and the trans can be put back together.
__________________
And God created Neil Peart so that lightning would make sense to the world.
~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
11-04-2012, 12:54 PM | #170 |
Welcome to America!
|
Ya gotta hate when a project gets to this stage...you can see it, smell it, taste it.
__________________
91 GT Convertible 2006 Nissan Titan LE Crew Cab 2014 Peterbilt 337/Marion 22' box |
|
|