|
02-17-2010, 09:11 PM
|
#1 |
|
Junior Member
Join Date: Feb 2010
Location: Anniston,AL
Posts: 28
|
New Starter Prob..
Ight i put the new flywheel in and it started up perfectly but now when i try to start the car now it still grinds but its not as bad as used to and when i left off of the key it act like the starter kinda keeps going or just stays enganged when i let off the key its acting like it going backwards or somthing like that any ideas this time around?
__________________
89 Mustang GT 302 Cubic Inches Crane Cam Setup Holley 750 dbl Pump Whole Lota Gittyup |
|
|
|
02-17-2010, 09:28 PM
|
#2 |
|
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Bendix is not disengaging. Need to check the wiring at the starter
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP  2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
|
|
|
|
02-17-2010, 09:48 PM
|
#3 | |
|
Junior Member
Join Date: Feb 2010
Location: Anniston,AL
Posts: 28
|
Quote:
__________________
89 Mustang GT 302 Cubic Inches Crane Cam Setup Holley 750 dbl Pump Whole Lota Gittyup |
|
|
|
|
|
02-18-2010, 04:20 AM
|
#4 |
|
Dayuuuuuuum!!!!!
Join Date: Dec 2004
Location: Dallas GA
Posts: 2,933
|
Thats the correct wiring for a mini starter.
Check your ignition switch next to see if it is hanging.Ignition switches were common issues in fox body cars so I'd just replace it if I were you
__________________
86 Mustang Gt......Mods piling up in my garage.
07 F350 dooly.....Tows my fifth wheel |
|
|
|
|
02-18-2010, 02:07 PM
|
#5 | |
|
Junior Member
Join Date: Feb 2010
Location: Anniston,AL
Posts: 28
|
Quote:
if thats it then that sucks cuz i dont have all that much more money to put into this car i already put like 2500 in it(thats alot for me) to get it like it is but ill try soon
__________________
89 Mustang GT 302 Cubic Inches Crane Cam Setup Holley 750 dbl Pump Whole Lota Gittyup |
|
|
|
|
|
02-18-2010, 10:08 PM
|
#6 |
|
Junior Member
Join Date: Feb 2010
Location: Anniston,AL
Posts: 28
|
I even put shim on it and it still does it
__________________
89 Mustang GT 302 Cubic Inches Crane Cam Setup Holley 750 dbl Pump Whole Lota Gittyup |
|
|
|
|
02-18-2010, 11:00 PM
|
#7 |
|
Member
Join Date: Dec 2008
Location: UCLA
Posts: 68
|
after it is cranked and running, check to see if the starter side of the solenoid still has fire. if it does it could be a bad solenoid. also check if it still has fire to see if the the start wire( the one on the little stud) still has fire. if so, then this would indicate a bad ignition switch, which is about a 15 dollar part. these things are notorious for going bad. hope this helps.
|
|
|
|
|
02-18-2010, 11:05 PM
|
#8 |
|
Member
Join Date: Dec 2008
Location: UCLA
Posts: 68
|
just noticed that you put on a mini starter. does it have the solenoid build into the starter? if so i would wire it a little differently. this could be your problem.
|
|
|
|
|
02-18-2010, 11:44 PM
|
#9 | |
|
Junior Member
Join Date: Feb 2010
Location: Anniston,AL
Posts: 28
|
Quote:
and are u talking about to the key switch or the mechanical parts? of the switch
__________________
89 Mustang GT 302 Cubic Inches Crane Cam Setup Holley 750 dbl Pump Whole Lota Gittyup Last edited by 89StangRompt; 02-19-2010 at 12:50 AM. |
|
|
|
|
|
02-19-2010, 01:49 AM
|
#10 |
|
Member
Join Date: Dec 2008
Location: UCLA
Posts: 68
|
the electrical part inside the column. i would wire the factory solenoid just as it was from the factory and i would put a jumper wire across the two terminals at the starter. hope this helps.
|
|
|
|
 |
|
|
Linear Mode
