03-17-2008, 03:07 PM | #1 |
Mind Blowing
Join Date: Jun 2006
Location: Dawsonville Ga
Posts: 3,913
|
Converting fogger to plate
we got a compucar fogger kit and a nos plate. We just ran lines to the plate and used nos jets. The only jets we had was for my sniper fogger on my car. So we looked at snipper plate kit jet chart and we had the jets for a 125 shot. But the car only picked up 3 tenths in the 1/8 mile. What did we not do right any help would be great. Thx
__________________
Slow Joe Racing 2008 dodge ram 5.7 HEMI 1993 lx with a 289 and a 3 speed on the floor WTB 1955 t-bird project |
03-17-2008, 04:00 PM | #2 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
What was the 60' time? What was your bottle pressure? What is your timing set to?
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
03-17-2008, 04:25 PM | #3 |
Mind Blowing
Join Date: Jun 2006
Location: Dawsonville Ga
Posts: 3,913
|
60 ft was like 1.8s i think bottle was around 900 psi and timing was lowered 2 degrees from what is was. Not sure what it was before that i will get waypastcrazy to get in on this.
__________________
Slow Joe Racing 2008 dodge ram 5.7 HEMI 1993 lx with a 289 and a 3 speed on the floor WTB 1955 t-bird project |
03-17-2008, 04:29 PM | #4 |
ADDICTED TO SMALL BLOCKS
Join Date: Jan 2007
Location: lookout mt
Posts: 1,757
|
60s were 1.8 pressure was 900 timing was 34 then 32 and then tried it at 36
__________________
http://alabamaopencarry.com/forum/index.php One of StreetStangs class clowns! Status:slow as hell! NORTH EAST ALABAMA STANGS |
03-17-2008, 05:31 PM | #5 |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
That's a lot of timing for a nitrous car. Have you checked the plugs?
Also 900 psi is kinda of hurting you. You should have the bottle press at 1000 psi for optimum results. Are you leaving the launch pad on the jug? Based off your comments, I would say 3 tenths in the 1/8 is not that far off for a 125 shot running at 900 psi. Also if you are leaving the launch pad on juice and only cutting 1.8's, you are leaving at least another tenth or two on there.
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
03-17-2008, 06:22 PM | #6 |
Mind Blowing
Join Date: Jun 2006
Location: Dawsonville Ga
Posts: 3,913
|
yes we was on it off the line. The car is all over the place got to do some work on that. I was not leaving that hard 2500-3000 rpm. Waypastcrazy and kev drove the car to and i think kev ran a 1.7 60ft with a 7.85 i think
__________________
Slow Joe Racing 2008 dodge ram 5.7 HEMI 1993 lx with a 289 and a 3 speed on the floor WTB 1955 t-bird project |
03-17-2008, 06:24 PM | #7 | |
ADDICTED TO SMALL BLOCKS
Join Date: Jan 2007
Location: lookout mt
Posts: 1,757
|
Quote:
leaving launch pad at 3000 rpm nos it on a wide open throttle switch
__________________
http://alabamaopencarry.com/forum/index.php One of StreetStangs class clowns! Status:slow as hell! NORTH EAST ALABAMA STANGS |
|
03-17-2008, 06:32 PM | #8 |
ADDICTED TO SMALL BLOCKS
Join Date: Jan 2007
Location: lookout mt
Posts: 1,757
|
engine runs very smooth no misses at all
__________________
http://alabamaopencarry.com/forum/index.php One of StreetStangs class clowns! Status:slow as hell! NORTH EAST ALABAMA STANGS |
03-17-2008, 07:48 PM | #9 | |
3v's are slow
Join Date: Dec 2004
Location: Here and There
Posts: 17,152
|
Quote:
I can't find a table to tell you what jets should be used for a 125 shot plate kit. Why were you guys launching so low? Because of traction issues? You have to launch harder to get the full advantage of nitrous. ( the sudden torque hit) Up to at least a 5k rpm launch. Then you will see your true improvements
__________________
2009 Porsche Carrera S 2008 ///AMG C63.. Eurocharge Tune. RIP 2019 AMG GLC43..wife's 03 F250 SD.. Edge Evo, AFE Stage 1 CAI 08 GT. JBA axle back, FRPP springs, FRPP swaybars.. daughter's 01 Cobra vert... wife's I need a new toy |
|
03-17-2008, 08:07 PM | #10 |
Dayuuuuuuum!!!!!
Join Date: Dec 2004
Location: Dallas GA
Posts: 2,933
|
I run my timing at 32 degrees total on my 100 shot.For the setup you have you really need 950-1000 psi bottle pressure.
I will look for my jet chart and see what you should have in there
__________________
86 Mustang Gt......Mods piling up in my garage.
07 F350 dooly.....Tows my fifth wheel |
|
|